Custom Code Setting; Switching The Upper Limit Of Cooling Temperature; Dip Switch Setting; Function Setting - Fujitsu AIRSTAGE ASYE07GACH Manual De Instalación

Example
If 4 indoor units are connected.
Indoor unit Indoor unit
RC AD SW RC AD SW
0 1
Remote
controller
RC AD SW 0 1
Address 0 1
RC AD SW 8 9
Address 8 9
ii) 2-wire type
Rotary switch (RC AD SW)...Factory setting "0"
Since the remote controller address settings are automatically confi gured, you do not
need to confi gure them.
If confi guring manually, it is necessary to confi gure both the indoor unit and the
remote controller. For details, please refer to the remote controller manual.

6.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Confusion
Indoor
unit
Remote
controller
Custom code setting for indoor unit
Set the DIP switch SET 3 SW1, SW2 referring to the Table B.
DIP switch (SET 3)
OFF ON
SW1
SW2
SET 3
SW3
SW4
Table B
A (Factory setting)
DIP switch SET 3
OFF
SW1
DIP switch SET 3
OFF
SW2

6.3. Switching the upper limit of cooling temperature

This setting can be raised the upper limit of the cooling temperature setting range.
This setting can be used when connecting to the following controllers.
• Wired remote controller (2-wire type)
• Central remote controller
• Touch panel controller
• System controller
• Service tool
• Web monitoring tool
En-9
9377773098-01_IM.indb 9 9377773098-01_IM.indb 9
Indoor unit Indoor unit
RC AD SW RC AD SW
2 3
2 3 4 5 6 7
2 3 4 5 6 7
A B C D E F
10 11 12 13 14 15
Code change
A B C D
A B C D
Controller PCB
Custom code
B C
ON OFF
OFF ON

DIP switch setting

Set the DIP switch SET 4 SW3 referring to the Table C.
DIP switch (SET 4)
OFF ON
SW1
SW2
SW3
SW4
Table C
DIP switch SET 4 SW3
OFF (Factory setting)
ON
NOTE :
Please do not make a standard setup and an extension setup intermingled in remote
controller group.

6.4. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
(Set IU AD, REF AD SW to 0)
• Refer to "6.1. Setting the address" for indoor unit address and refrigerant circuit ad-
dress settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function Setting number Default
number
00
Filter
indicator 11
01
interval
02
00
Filter 01
indicator 13
Display only
action
02
D
00
Cool air
ON
temperature 30
01
trigger
ON
02
00
Heat air
01
temperature 31
02
trigger
03
00
Auto
40
restart
01
00
Cool Air
Preven- 43
tion
01
the remote
Controller PCB
SET 4
Cooling temperature setting range
Standard (18 to 30 °C)
Extension (18 to 32 °C)
Details
○
Default
Adjust the fi lter cleaning interval notifi ca-
tion. If the notifi cation is too early, change
Longer
to setting 01. If the notifi cation is too late,
change to setting 02.
Shorter
○
Enable
Disable Enable or disable the fi lter indicator. Set-
ting 02 is for use with a central remote
controller.
on central
remote
controller
○
Default
Adjust the cool air trigger temperature. To
lower the trigger temperature, use setting
Adjust (1)
01. To raise the trigger temperature, use
setting 02.
Adjust (2)
○
Default
Adjust the heat air trigger temperature. To
lower the trigger temperature by 6 degrees C,
Adjust (1)
use setting 01. To lower the trigger tempera-
Adjust (2)
ture by 4 degrees C, use setting 02. To raise
the trigger temperature, use setting 03.
Adjust (3)
Enable
Enable or disable automatic system
○
restart after a power outage.
Disable
○
Super low
Restrain the cold airfl ow with making the
airfl ow lower when starting heating op-
Follow the
eration. To correspond to the ventilation,
setting on
set to 01.
controller
7/12/2012 3:05:25 PM 7/12/2012 3:05:25 PM