Connecting The Cutting-Means Assembly To The Ride-On Mower - Stiga 100 Combi 3 EL QF Manual De Uso

Ocultar thumbs Ver también para 100 Combi 3 EL QF:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 113
For storage and transport purposes, some 
components of the machine are not installed 
in the factory and have to be assembled after 
unpacking. Follow the instructions below.
Unpacking and completing the
assembly should be done on a flat and
stable surface, with enough space for
machine handling and its packaging,
always making use of suitable equipment.
Do not use the machine until all the
indications provided in the "ASSEMBLY"
section have been carried out.
Always wear protective gloves.
4.1 UNPACKING
1. Cautiously open the packaging, paying 
attention not to lose components.
2. Consult the documentation in the 
box, including these instructions.
3. Remove all the unassembled 
parts from the box.
4. Remove the machine from the box.
5. Dispose of the box and packaging in 
compliance with local regulations.
4.2 CONNECTING THE CUTTING-MEANS
ASSEMBLY TO THE RIDE-ON MOWER
The cutting-means assembly is connected 
to the ride-on mower using:
• the supports fastened to the front wheels,
• the spring and chain that is connected 
to the accessory lifting hook
• the cutting-means transmission 
belt (preassembled on the 
cutting-means assembly),
• the canvas guard support chassis.
4.2.1 Coupling the belt protection
connection device
1. Undo the two screws (fig. 4.A) preassembled 
on the front section of the mower.
2. Position the chassis support device 
(fig. 4.B) and fasten in place with 
the two screws (fig. 4.A).
4.2.2 Basic alignment
The basic alignment of the cutting-means 
assembly requires the rear edge to be 
raised 5 mm higher than the front edge.
This means that the cutting-means 
assembly is slanting forwards.
To adjust the height of the cutting-
means assembly:
1. Lift the cutting-means assembly slightly to 
reduce the load on the split pin (fig. 5.A).
2. Remove the split (fig. 5.A) and the 
washer (fig. 5.B) preassembled in the 
pin (fig. 5.C), using a screwdriver.
3. Adjust the height of the rod and insert
the washer and the split pin in one of the 
designated holes (fig. 6.A), positioning 
it as seen in the diagram (fig. 6.B):
– For machines fitted with 17 inch 
wheels: position the split pins in 
the highest hole on the rod.
– For machines fitted with 16 inch 
wheels: position the split pins in 
the central hole on the rod.
4. Adjust the height of both the cutting-
means assembly support arms.
4.2.3 Coupling with the quick release
supports fixed to the wheels
IMPORTANT When performing the operations
below, please read the instructions in the
machine manual and the support system manual.
1. Check that the quick release supports 
are installed on the machine and on 
the cutting-means assembly arms.
2. Place the cutting-means assembly 
in front of the mower.
3. Rotate the quick release supports 
to the open position (fig. 7.A).
4. Lift and rest the lower section (fig. 7.B) of the 
pin coupling bracket (fig. 7.C) on both sides.
5. Connect the coupling bracket (fig. 8.A) 
to the pin (fig. 8.B) on both sides.
4.2.4 Coupling the cutting-means
transmission belt
• 4WD models
1. Use the left hand to grasp the tensioner 
lever (fig.9.A) and pull it outwards.
2. Use the right hand to move the 
belt onto the pulley (fig. 9.B).
3. Move the belt along the tensioner 
pulley (fig. 9.C) whilst slowly 
releasing the tension and grip.
• 2WD model
1. Use the left hand to grasp the tensioner 
lever (fig. 9.A) and pull it outwards.
2. Use the right hand to move the 
belt onto the pulley (fig. 9.B).
3. Move the belt along the tensioner 
pulley (fig. 9.C) whilst slowly 
releasing the tension and grip.
EN - 5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

100c e qf

Tabla de contenido