Workplace - Fein STS325R Manual De Instrucciones

OBJ_BUCH-0000000098-003.book Page 15 Thursday, October 20, 2016 4:52 PM
Character Unit of measurement,
international
2
m/s
2
m/s
h,D
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this pneumatic tool before you have
thoroughly read and completely understood this
Instruction Manual. The documents mentioned
should be kept for later use and enclosed with the pneu-
matic tool, should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the pneumatic tool:
Hand-guided compressed air hacksaw for commercial use
for cutting round and other shaped work pieces of metal,
plastic and cement in weather-protected environments
using the application tools and accessories recommended
by FEIN.
Safety instructions.

Workplace

Keep work area clean and tidy. Cluttered or dark work
areas invite accidents.
Do not operate the pneumatic tool in explosive atmos-
pheres, such as in the presence of flammable liquids,
gases or dusts. Pneumatic tools create sparks which can
ignite the dust or fumes.
Keep children and bystanders away while operating the
pneumatic tool. Distractions can cause you to lose con-
trol over the pneumatic tool.
Safety when handling compressed air
Clean the compressed-air supply regularly. Protect the
hose from kinks, contraction, heat, and sharp edges.
Firmly tighten the hose clamps. Have damaged hoses and
couplings repaired immediately. In case of malfunctions
to the air supply, the compressed-air hose can be thrown
about and lead to injury. Raised dust or chips may cause
serious eye injury.
Personal safety
Stay alert, watch what you are doing, and use common
sense when operating a pneumatic tool. Do not use a
pneumatic tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention
while operating a pneumatic tool may result in personal
injury.
Unit of measurement, Explanation
national
2
m/s Vibrational emission value according
(vector sum of three directions)
2
m/s Mean vibrational value for sawing
m, s, kg, A, mm, V, Basic and derived units of measurement from
W, Hz, N, °C, dB, the international system of units SI.
2
min, m/s
Use personal protective equipment. Always wear eye pro-
tection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Make sure that the switch
is in the "OFF" position before connecting the pneumatic
tool to the compressed-air supply. When your finger is
on the switch while carrying the pneumatic tool or when
connecting the pneumatic tool to the compressed-air
supply while it is switched on, accidents can occur.
Remove any adjustment tools or spanners before switch-
ing on the pneumatic tool. An adjustment tool or spanner
left attached to a rotating part of a pneumatic tool may
result in personal injury.
Do not overreach. Keep proper footing and balance at all
times. This enables better control of the pneumatic tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
If devices are provided for the connection of dust extrac-
tion and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce
dust-related hazards.
Pneumatic tool use and care
Do not overload the pneumatic tool. Use the application
tool intended for your work. The correct pneumatic tool
will do the job better and safer at the rate for which it is
designed.
Do not use a pneumatic tool that has a defective switch.
A pneumatic tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the energy supply before making any pneu-
matic tool adjustments, changing accessories, or placing
the pneumatic tool aside. This safety measure prevents
accidental starting of the tool.
Store idle pneumatic tools out of the reach of children. Do
not allow persons unfamiliar with the pneumatic tool or
these instructions to operate the pneumatic tool. Pneu-
matic tools are dangerous in the hands of untrained users.
Maintain the pneumatic tool with care. Check for mis-
alignment or binding of moving pneumatic tool parts,
breakage of parts and any other condition that may affect
the pneumatic tool's operation. Have damaged parts
repaired before using the pneumatic tool. Many accidents
are caused by poorly maintained pneumatic tools.
en
15