Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1.
For your own safety, read the instruction manual
before operating the machine. Learning the machine's
application, limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.
Wear eye and hearing protection and always use
2.
safety glasses. Everyday eyeglasses are not safety
glasses. Use certified safety equipment. Eye protection
equipment should comply with ANSI Z87.1 standards.
Hearing equipment should comply with ANSI S3.19
standards.
3.
Wear proper apparel.
neckties, rings, bracelets, or other jewelry which may get
caught in moving parts. Nonslip protective footwear is
recommended. Wear protective hair covering to contain
long hair.
4.
do not use the machine in a dangerous environment.
The use of power tools in damp or wet locations or in rain
can cause shock or electrocution. Keep your work area
well-lit to prevent tripping or placing arms, hands, and
fingers in danger.
5.
do not operate electric tools near flammable liquids
or in gaseous or explosive atmospheres. Motors and
switches in these tools may spark and ignite fumes.
Maintain all tools and machines in peak condition.
6.
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.
Check for damaged parts.
7.
check for any damaged parts. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
and any other conditions that may affect its operation.
A guard or any other part that is damaged should be
properly repaired or replaced with DELTA or factory
authorized replacement parts. Damaged parts can cause
further damage to the machine and/or injury.
8.
Keep the work area clean.
invite accidents.
Keep children and visitors away.
9.
potentially dangerous environment. Children and visitors
can be injured.
10.
Reduce the risk of unintentional starting.
that the switch is in the "OFF" position before plugging in
the power cord. In the event of a power failure, move the
switch to the "OFF" position. An accidental start-up can
cause injury. Do not touch the plug's metal prongs when
unplugging or plugging in the cord.
11.
Use the guards.
Check to see that all safety devices are
in place, secured, and working correctly to prevent injury.
12.
Remove adjusting keys and wrenches before starting
the machine. Tools, scrap pieces, and other debris can
be thrown at high speed, causing injury.
Use the right machine.
13.
attachment to do a job for which it was not designed.
Damage to the machine and/or injury may result.
14.
Use recommended accessories.
and attachments not recommended by DELTA may cause
damage to the machine or injury to the user.
gENERAL SAFETY RULES
Failure to follow these rules may result in serious personal injury.
Do not wear loose clothing, gloves,
Before using the machine,
Cluttered areas and benches
Your shop is a
Make sure
Don't force a machine or an
The use of accessories
15.
Use the proper extension cord.
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will
cause a drop in line voltage, resulting in loss of power and
overheating. See the ExTENSION CORd CHART for the
correct size depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Secure the workpiece.
16.
workpiece when practical. Loss of control of a workpiece
can cause injury.
17.
Feed the workpiece against the direction of the
rotation of the blade, cutter, or abrasive surface.
Feeding it from the other direction will cause the
workpiece to be thrown out at high speed.
18.
don't force the workpiece on the machine.
the machine and/or injury may result.
don't overreach.
19.
a working machine, causing injury.
20.
Never stand on the machine.
tool tips, or if you accidentally contact the cutting tool.
21.
Never leave the machine running unattended.
the power off. Don't leave the machine until it comes to a
complete stop. A child or visitor could be injured.
22.
the machine "OFF", and disconnect the machine from
the power source and wait 2-1/2 minutes to allow time
for internal rotating components to stop before installing
or removing accessories, changing cutters, adjusting,
changing set-ups or clearing clogs. When making repairs,
be sure to lock the start switch in the "OFF" position. An
accidental start-up can cause injury.
Make your workshop childproof with padlocks, master
23.
switches, or by removing starter keys. The accidental
start-up of a machine by a child or visitor could cause
injury.
Stay alert, watch what you are doing, and use
24.
common sense. Do not use the machine when you
are tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating
power tools may result in injury.
25.
disperse dust or other airborne particles, including
wood dust, crystalline silica dust and asbestos dust.
Direct particles away from face and body. Always operate
tool in well ventilated area and provide for proper dust
removal. Use dust collection system wherever possible.
Exposure to the dust may cause serious and permanent
respiratory or other injury, including silicosis (a serious
lung disease), cancer, and death. Avoid breathing the
dust, and avoid prolonged contact with dust. Allowing
dust to get into your mouth or eyes, or lay on your skin
may promote absorption of harmful material. Always
use properly fitting NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure, and wash
exposed areas with soap and water.
3 -
English
Make sure your
Use clamps or a vise to hold the
Loss of balance can make you fall into
Injury could occur if the
SEVERE LACERATION HAzARd. Turn
Use of this tool can generate and
Damage to
Turn
Publicidad
Tabla de contenido
