Listening To The Radio; Playing Cds - AEG KRC 4376 CD Instrucciones De Servicio

English
42 42
2. Successively, you can now set the hours and minutes.
VOLUME + /VOLUME – buttons
Adjust to your preferred volume level.
MUTE button (27 on the remote control)
You can quickly shut off the sound using the MUTE button.
The currently set volume is flashing in the display. Press the
button again to turn the sound back on.

Listening to the radio

Hints for FM Reception
• The FM reception depends on the location.
Follow the steps below:
- Fully unwind the wire antenna.
- If necessary, change the position of the wire antenna to
improve the reception.
• Depending on the location, some station may not be
received in your region or only with interference. This is
not a malfunction of the device!
Scanning stations
1. Use the SOURCE button to select the radio mode.
2. Tune the desired stations with the
When holding down either of the buttons, the device will
start scanning until the next radio station is found. The
display will show the respective frequency.
3. If there is interference on the received station, try to
improve the reception by rotating, winding or unwinding
the wire antenna.
Presetting radio stations
The device can preset up to 20 radio stations. To preset a
station, follow the steps below:
1. Search for a station as described in "Scanning stations".
2. Press the CLK SET / MEM / PROG button. The storage
space appears in the display, and the text "MEM" starts
flashing.
3. Use the / M + and / M – buttons to choose the preset
location for the corresponding station.
4. Press the CLK SET / MEM / PROG button again. The
station will be preset. The frequency of the preset radio
station will be displayed.
Recalling preset radio stations
Use the / M + and / M – buttons to select the memory
locations.

Playing CDs

NOTE:
Observe the following operation for the replay of CD' s
in the MP3 format! The device is not MP3 capable. The
message „ " appears in the display.
KRC4376CD_IM
This is how you play a CD
1. Select the CD mode with the SOURCE button. The
following will appear in the display " – – – – ".
2. Press the OPEN / CLOSE button to open the CD tray.
3. Place the CD into the CD tray with the label side up. Press
the OPEN / CLOSE button once more to close the CD
tray again.
4. The CD will play from the first title. The current title num-
ber and the notification " " are shown on the display.
Then the present playback time of the current track
appears.
5. In order to remove a CD, please press the STOP / M –
button, open the CD compartment and lift the CD out
carefully.
Always keep the CD tray closed.
NOTE:
• If a disc is inserted the wrong way around, respectively
if no disc is inserted, then the message " – – – – " will
blink and " " appears on the display.
• Playback of CDs produced by the user cannot be
guaranteed due to the large variety of software and CD
media available.
• Please note:
There are many burning and compression methods,
and buttons.
as well as quality differences between CDs and burned
CDs.
The music industry furthermore does not observe any
fixed standards (copyright protection).
For these reasons, in rare cases there may be problems
when playing CDs. This is not a malfunction of the
device.
Description of the CD buttons
/ M +
You can briefly interrupt and resume playback using this
button. The symbol " " will flash on the display. Pressing
again continues playback.
SKIP / TUNE
With
If the button is kept pressed down, the machine starts to
search through the tracks.
The
Press once
Press twice
Press three times = This plays the song before etc. If the
/ M –
The CD stops.
you can jump to the next or previous track etc.
button can be used as follows:
= This starts the current track again from
the beginning.
= This jumps back to the previous track.
button is kept pressed down, the
machine starts to search through the
tracks.
06.05.16