Wolf Garten LI-ION POWER 34 Instrucciones De Funcionamiento Originales página 15

Charging the battery
1
Caution! The charger must only be operated in dry
rooms!
3
General charging instructions
To prolong the service life of the battery, observe the follow-
ing instructions:
z Before first use, the battery needs to be charged for
about 5-6 hours.
z If the battery voltage is too low, the lawnmower switches
off automatically. In such a case, recharge the battery.
z The Lithium iron battery must also be recharged before
prolonged periods of non-use, for example at the begin-
ning of winter.
z The charging time is 5-6 hours for a battery that is com-
pletely empty.
z The Lithium ion battery can be recharged at any charge
level, and charging can be interrupted and resumed with-
out any damage to the battery (no memory effect).
1. Remove the contact key
2. Release the battery cover by pushing it down
3. Remove the battery from the recess
4. Connect the battery to the charger
5. Connect the charger to the mains socket (230 V
3
Instructions for the handling of the charger:
z Red LED is on: Battery is being charged
z Green LED is on: Charge process completed
z If the charger is connected to a power socket without a
battery, the LEDs are off.
z In order to prolong the life the battery, it should not be
charged for a period longer than two days.
3
Instructions regarding the charge status indicators:
Green LED is on:
–
Battery capacity =
Yellow LED is on:
–
Battery capacity =
Red LED flashing (battery nearly flat):
–
Battery capacity =
–
The battery should be recharged
Red LED is continuously on (device switches
off):
–
Battery capacity =
or
–
fault (e.g. battery too hot)
Hang up collection bag
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the mo-
tor is switched off and the cutting tool has come to a stand-
still.
z Switch off the motor and remove the contact key.
z Do not attach the collection bag until your feet are at a
safe distance from the cutting tool.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the reces-
ses (see arrow).
3. Replace the protective flap.
G
K .
L .
M
.
N
.
~ )
O
Set cut height
1
Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after
the motor is switched off and the cutting tool has come to a
standstill.
z Switch off the motor and remove the contact key.
1. Pull the lever out.
2. Set the desired cutting height.
3. Press the lever back in.
Selection of Cutting height
z If possible, mow when grass is dry in order to protect turf. Do
not se cutting position too low when mowing very hight or wet
grass.
z We recommend an average cutting height of 40-50 mm.
Starting and Stoping
z Switch on motor with mowerplaced on level and firm ground.
z not in high grass - alternatively tilt slightly
Switch-on motor
1. Depress button and hold (1).
2. Lift up bar (2).
N
.
3. Release button (1).
Switch-off motor
Release bar (2).
3
Tip for mowing:
To prevent strips of grass from being left unmowed, the cut-
ting paths must always overlap a few centimeters
Overload protection
3
In case of overload or blocking, the motor shuts down
automatically!
Switch off the motor and remove the contact key.
z Overload: Cutting height is too low, or forward speed is
too fast
z Blocking: Foreign object in cutting area (e.g. branches)
z The machine can be switched on again after about 5
min.
Emptying of Grassbox
When the collection bag is full, the flap lowers by itself.
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Switch off the motor and remove the contact key.
z Empty collection bag.
z Remove potential blockages in the cutting space before
starting.
3
Instructions for level indicator:
For an efficient functioning of the level indicator, regularly
clean the holes under the level indicator in the collection
bag with a hand brush.
P
R
R
T
Q
.
S
15