Technical Data; Proper Use; Before Starting - Hurricane HRT 35 Manual De Instrucciones

Anleitung HRT 35 SPK 7 24.08.2005
GB
/ VDE 0282 with a minimum diameter of 1.5 mm
Plug connectors must be equipped with earthing
contacts and the coupling must be rain-water-
protected.
Keep cables and other objects out of the area
you want to cut.
If you have to lift the grass trimmer to move it,
switch off the motor and wait for the rotating tool
to stop. Before you leave the trimmer, switch off
the motor and pull out the power plug.
Before you connect the grass trimmer to the
power supply, make sure that none of its moving
parts are damaged and that the line spool is
correctly inserted and fastened.
Never cut against hard objects when using the
grass trimmer. This is imperative to avoid
causing injury to the user and damage to the
trimmer.
Use only original replacement parts for repair
and maintenance purposes.
Have repairs carried out only by a qualified
electrician.
Examine the grass trimmer for signs of wear or
damage each time before you use it and after
any collisions. Have essential repairs carried out
without delay.
Always keep your hands and feet away from the
cutting mechanism, particularly when you switch
on the trimmer.
After pulling out new line, always return the
trimmer to normal working position before you
switch it on again.
Never use replacement parts or accessories
which are not foreseen or recommended by the
manufacturer.
Pull out the power plug before carrying out any
inspection, cleaning or other work on the trimmer
and whenever it is not being used.
Caution! The nylon line will run on for a few
seconds after the tool is switched off!
Tool runs
on!
3. Symbols used on the appliance (see
Figure 2)
Item 1: Warning
Item 2: Wear eye protection
Item 3: Protect from moisture
Item 4: Read the instruction manual before starting
Item 5: Pull out the mains plug before checking a
damaged power cable
Item 6: Keep other people out of the danger area
Item 7: The tool continues to rotate
12
10:48 Uhr Seite 12
2 .

4. Technical data

Voltage 230V ~ 50 Hz
Power rating
Cutting width
Speed
Nylon cutting line
Sound pressure level LPA
Sound power level
Vibration aw max. 5,3 m/s
Weight
The noise level of this machine may exceed 85
dB(A). In this case, noise protection measures need
to be introduced for the user. The machine's noise
was measured in accordance with IEC 59 CO 11,
IEC 704, DIN 45635 Part 21, NFS 31-031
(84/538/EEC).
The value of the vibrations emitted on the hand is
max. 5.3 m/s 2 . This value was determined in
compliance with EN 786 Appendix D: 1996+A1:
2001.
5. Assembling the grass trimmer
To install the handle on the telescopic tube
Fit the handle on the telescopic tube and insert it
as far as possible (Figure 3). The button (1) will
engage automatically.
To install the safety hood
Place the safety hood on the motor head (Figure
4) and then turn it clockwise until it engages
(Figure 5). Secure it with the screws supplied
(Figure 5).

6. Proper use

The trimmer is designed for cutting lawns and small
areas of grass in private and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer's
directions for use.
Important! It is prohibited to use the tool to chop
material for composting because of the potential
danger to persons and property.

7. Before starting

You can adjust the height of the grass trimmer and
the position of the auxiliary handle to obtain the
optimal working position.
Height adjustment
Place the grass trimmer on a firm surface. You can
adjust its height to suit your own height by undoing
the rotary knob (Figure 6 Item 1) and then adjusting
350 W
ø 25 cm
11.000 rpm
ø 1.2 mm
83 dB(A)
93 dB(A)
2
2,1 kg