Nozzle Attachments (16) And (17); Assembly The Wall Holder; Inserting The Plug Of The Power Supply Unit; Fastening The Wall Holder - BOMANN BS 1949 A CB Instrucciones De Servicio

Nozzle Attachments (16) and (17)

You can attach these two nozzle attachments directly to the
hand unit or to the already installed suction pipe.
Connection at the Hand Unit
• Insert a nozzle attachment with the marking facing up into
the connection at the hand unit. It must audibly engage.
• To disconnect the nozzle attachment, press the release
(14) and pull out the attachment at the same time.
Connection to the Suction Pipe
You need the adapter (15) for connection to the suction pipe.
• Insert the adapter with the angular side into the lower end
of the suction pipe.
• Now you can slip a nozzle attachment onto the round side
of the adapter.
• For removal of the nozzle attachment and the adapter,
just pull the parts off.
Combined Crevice / Brush Nozzle
With this nozzle, you can selectively vacuum corners and
slots.
Use the nozzle with locked brush to prevent scratching of the
surface to be cleaned.
• For this, press the button
the brush to the end of the nozzle. It
must engage.
• Press the button again to unlock the
brush.
Upholstery Brush
This nozzle is especially good for gentle cleaning of larger
susceptible surfaces.

Assembly the Wall Holder

Inserting the Plug of the Power Supply Unit

If you want to use the wall holder also as the charging station,
attach the plug of the power supply unit first. Refer to the
illustrations (A to C) on page 3.
NOTE:
• Turn the plug at the metal end, not at the cable. Use a
pliers if necessary.
• There is an opening at the rear of the wall holder. You
can turn the plug additionally with a finger through this
opening.
1. Set the plug of the power supply unit with the flattened
side into the wall holder. (Fig. A)
2. Turn the plug of the power supply unit by 90 °. It must
sit solidly in the holder and sliding no longer shall be
possible. (Fig. B)
3. Fix the cable in the cable guide. (Fig. C)
BS1949ACB_IM
and push

Fastening the Wall Holder

WARNING:
Make sure beforehand whether there are cables in the wall
which could be damaged!
CAUTION:
Place the wall holder so that the appliance is not exposed
to direct sunlight or other heat sources.
NOTE:
A power outlet must be near.
1. Measure the height for the wall holder. Hold the vacuum
cleaner against the wall with the suction pipe and the floor
nozzle installed.
2. Hold the wall holder against the wall as shown on page 3.
Mark 2 drill holes.
3. Drill the holes and insert the wall plugs into the wall.
4. Insert the screws through the holes of the wall holder.
5. Tighten the screws with a screwdriver hand-tight.

Charging the Battery

1. Turn off the device.
2. Connect the power supply unit with the connection
socket (5). If you have prepared the wall holder as a
charging station, suspend the appliance from the wall
holder.
3. Connect the mains adapter to a certified wall socket.
Charge the device for approx. 5 hours before first-time
use.
NOTE:
• The LED charge indication shows the charging sta-
tus of the rechargeable battery. (25 %, 50 %, 100 %)
• The appliance has electronic charge control, which
prevents overcharging.
• Charging has been completed when all 3 LEDs
are lit.
• The LEDs go out after a while.
• It is normal for the device to heat up during charging.
4. The rechargeable battery must be charged when the LED
charge indication shows only 25 % of capacity.
5. Disconnect the power supply unit from the outlet once the
rechargeable battery has been charged completely.
NOTE:
Even when switched off, the rechargeable battery dis-
charges continuously. If the device is out of use for a longer
period of time, charge the rechargeable battery at least
once every 6 to 12 weeks.
43
20.10.16