Hoover SE71_SE41 Sprint Evo Manual De Instrucciones página 5

Pet Hair Remover mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep cleaning
on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal. [1X]
Allergen Remover mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [1y]
Parquet Nozzle* – For parquet floors and other delicate floors. [1Z]
ImPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
ClEANER mAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
ImPORTANT: To maintain optimum performance, do not allow the dust to sit higher than the
max level.
1. Release the dust container by sliding the dust container release button towards the front
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release any
excess dust from the filter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and use
the other hand to press the Dust Container Flap Opening Button to release the dust into
the bin. [15]
4. Close the Dust Container Flap and refit the Dust Container to the cleaner main body.
Cleaning the washable Filters
The cleaner is fitted with a pre-motor and exhaust filter. To maintain optimum cleaning
performance, regularly clean the filters. Remove excess dust from the filters by gently tapping
them against the side of a bin. The filters should be washed after every 5 container empties.
ImPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
ImPORTANT: Regularly check and maintain the filters by following the filter maintenance
instructions, it is also recommended that you purchase new filters after every 3rd filter
wash. This will maintain your cleaners performance.
To access the pre-motor filter:
1. Empty the Dust Container as described in 'Emptying the Dust Container' . Then, keeping
the Dust Container Flap open:
2. Remove the pre-motor filter by rotating it clockwise at the bottom of the Dust Container. [16]
3. separate the protective mesh from the filter. [17] Gently tap both the protective mesh
and the filter against the side of a bin to remove excess dust and wash both of them
under warm water. [18] Do not use hot water or detergents.
4. Remove excess water from the filter and leave it to dry fully before reusing. [21]
*Certain Models Only ** Certain models only, nozzles may vary according to model
5. Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and refit
to cleaner.
ImPORTANT: Do not use the product without the pre-motor filter pack fitted.
ImPORTANT: Always ensure the filter packs are fully dry before use.
To access the exhaust filter:
1. Unclip the exhaust grid from the rear of the cleaner. [19]
2. separate the filter from the grid and wash the filter under warm water. [20] Do not use
hot water or detergents.
3. Remove excess water from the filter and leave to dry fully before reusing. [21]
4. Remount the filter into the grid and refit it to the cleaner.
Remember: Do not use hot water or detergents. In the unlikely event of the filters becoming
damaged, fit a Genuine Hoover consumable. Do not try and use the product without a filter fitted.
Removing a Blockage
1. Check if the Dust Container is full. If so refer to 'Emptying The Dust Container' .
2. If the Dust Container is empty, but suction is still low;
A. Do the filters need cleaning? If so refer to 'Cleaning the Washable Filters' .
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the tubes or hose.
C. Check for and clear any blockage in the Nozzle
wARNING - If the cleaner is used for a significant period of time with a blockage, a thermal cut
out will switch the cleaner off to prevent overheating. The bag check indicator turn green once
the cleaner has switched off to signal that the thermal cut out has been activated. If this should
happen, switch the cleaner off, unplug and correct the fault. It will take about 45 minutes for
the cut out to automatically reset.
USER CHECklIST
should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the Bag over-filled? Please refer to 'Cleaner Maintenance' .
• Is the filter blocked? Please refer to 'Cleaner Maintenance' .
• Is the hose or nozzle blocked? Please refer to 'Removing a Blockage' .
• Has the cleaner overheated? If so, it will take approximately 45 minutes to automatically
reset.
3
GB