Lutron PowPak Manual De Instalación

PowPakR | Installation
R
Dimming Module with EcoSystem
Part of the Energi TriPakR Family
RMJ-ECO32-DV-B | URMJ-ECO32-DVB
120 / 277 V~ 50 / 60 Hz 40 mA
UL 2043 Plenum Rated
EcoSystem : 18 V- 125 mA
®
Important Notes:
Please read before installing.
For installation by a qualified electrician in accordance with all
•
local and national electrical codes.
Note: Use copper conductors only.
•
Check to see that the device type and rating is suitable for the
•
application.
DO NOT install if product has any visible damage.
•
If moisture or condensation is evident, allow the product to dry
•
completely before installation.
Operate between 32 °F (0 °C) and 104 °F (40 °C).
•
0% to 90% humidity, non-condensing.
•
For indoor use only.
•
WARNING
Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.
PowPakR
Dimming Module
Install in center of room to
maximize RF coverage.
Radio
Powr SavrT
Occupancy
Sensor
30 ft (10 m)
Maximum
PicoR
Wireless
Control
40 ft (12 m)
All wireless transmitters must be installed within
30 ft (10 m) of the PowPakR Dimming Module.
Default Functionality
Occupancy Sensors
Occupied:
All lights 100%.
Unoccupied:
All lights off.
Daylight Sensor
All lights dim in response to daylight.
Link Cal.
Test
Wireless Transmitters
All lights 100%.
On:
All lights 50%.
Preset:
All lights off.
Off:
Daylight Override
Pressing the Raise " " button on an associated PicoR
wireless control will temporarily override daylighting for the
fixtures in that PicoR wireless control group.
Daylight Re-Enable
Daylighting will be re-enabled for that PicoR wireless
control group when one of the following occurs:
• Two hours have passed since the override.*
• ON, OFF or Preset button has been pressed on a
PicoR wireless control controlling that group.
• All associated Occupancy Sensors have reported
unoccupied.
* Each time a daylighting override occurs for any PicoR wireless
control group, the two hour timer is reset.
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg PA, 18036-1299, USA
Required Components
For each system ensure you have:
One PowPakR Dimming Module.
041372
Rev. D
Clear ConnectR
08/2014
LED
Raise
All On
EcoSystemR
+
LED
Lower
E1 & E2
EcoSystem
®
Bus Supply
(Class 1 or 2)
PowPakR Dimming Module
with EcoSystemR
(1 maximum)
Start Here
(For programming see reverse)
R
NOTE: PowPak Dimming Modules, wireless transmitters, and EcoSystem
will cause addressing or association issues. If replacing an existing PowPak
Mount, wire and install EcoSystem
1
devices and lighting fixtures
Connect power wiring (hot, neutral, ground) to each fixture.
Connect bus cable (E1 and E2) to each fixture.
Once complete, energize power to all fixtures, which should
turn on to full brightness. If fixtures do not go to full brightness,
check wiring and consult ballast installation guide.
Ground
Fixture Ground
White
NEU
N/C
Black
HOT
E1
E1
E2
E2
To additional EcoSystem ballasts or LED drivers.
®
NOTE - PLEASE READ:
3
A
Replacing an Existing
PowPakR Dimming Module
If you are replacing an existing
R
PowPak Dimming Module, you
MUST reset the new module
R
and connected EcoSystem
devices to factory defaults
(see Reset Factory Defaults).
Before beginning, make sure
R
all EcoSystem devices are
connected and powered. Doing
this will allow you to properly
associate wireless transmitters to
the new module in Step 3B.
Daylight calibration
4
Complete this step if the Daylight Sensor
should control all fixtures in the room equally.
Otherwise skip this step and see steps 5 and
10 on reverse.
Set lights in room to desired light level.
A
Press & hold the " Cal. " button for
B
6 seconds.
Exit room for 5 minutes
C
to allow calibration to be
completed.
Note: When calibration has
completed, all lights will flash and Link
the system will begin daylighting.
Need Help? www.lutron.com or call the Lutron
At least one Wireless Transmitter.
Radio Powr SavrT PicoR Wireless
Control
Occupancy/Vacancy Sensor
(9 maximum)
(6 maximum)
R
ballasts/drivers must be configured as a system. Pre-configuration of components
unit with a new one, pay special attention to the note in Step 3A.
®
Install PowPak
2
®
Dimming Module
When installing a PowPak
Module, use supplied conduit nut and
wire the module as shown.
Suggested Installation Location:
Install in center of room.
This ensures proper RF coverage of area.
If installing unit inside a junction box please see Application Note #423.
Typical
Once installed, energize the PowPak
EcoSystem
®
all fixtures. The fixtures will start at high-end and individually dim
ballast shown
when given an address. Once addressing is complete, all the
ballasts will return to high-end.
If ballasts are not properly addressing, see "Reset Factory Defaults" below.
Associate Wireless Transmitters to PowPakR Dimming Module
B
Before beginning this step, make sure that there are no other PowPakR modules being set up within the same building.
It is possible that wireless transmitters from other systems can be incorrectly associated to this system.
On the PowPak
1
Dimming Module,
hold the All On
button "
6 seconds until
ballasts flash.
The Clear Connect
LED will begin flashing
at a rate of
ON,
Troubleshooting
Fixtures cannot be controlled locally
from PowPakR Dimming Module.
Fixtures do not respond to wireless
transmitter(s).
Wireless transmitter(s) cannot be
associated to PowPakR Dimming Module.
PowPakR Clear ConnectR (Top) LED is on
solid and EcoSystem (Bottom) LED is
®
flashing.
Cal.
Test
Two or more replaced ballasts/LED drivers
are not responding as part of a group.
Technical Support Center at 1.800.523.9466
®
At least one EcoSystem
Hi-lume 3D digital ballast.
®
Please reference "Ballast Installation Best Practices Guide" P/N 041-170 at www.lutron.com
+
Link Cal.
Test
EcoSystem
Radio Powr SavrT
®
ballasts, or A-Series LED driver
Daylight Sensor
(1 maximum) (32 maximum. May be pre-installed in light fixtures.)
®
120/277 V~
50/60 Hz
Dimming
®
Green
(Ground)
Conduit
Nut
Dimming Module and
®
R Hold the indicated button on each wireless transmitter for 6 seconds. All ballasts will
2
flash to show wireless transmitters have been associated. *
" for
R
* If no g button, hold " Lights Off " button.
Hold the All On button "
3
⁄ second
1
2
association(s).
⁄ second OFF.
1
2
Permanently install wireless transmitters
4
information) .
Default: All wireless transmitters control all EcoSystemR devices.
www.lutron.com
• Ensure the breaker(s) to the PowPakR Dimming Module and ballasts
are on.
• Ensure that the E1 and E2 wires of the PowPakR Dimming Module
are wired to the ballast(s) / LED Driver(s) properly.
• The PowPakR Dimming Module is damaged or not functioning.
• Ensure the breaker(s) to the PowPakR Dimming Module and ballasts
are on.
• Ensure wireless transmitters are associated to the PowPakR Dimming
Module.
• The maximum number of wireless transmitters have been associated
to the PowPakR Dimming Module.
• The PowPakR Dimming Module has been replaced. See Step 3A.
• Daylight calibration has failed. Press any button on Pico wireless
®
control or PowPakR Dimming Module and restart calibration.
• Re-group replaced ballasts/LED drivers. See Step 5.
• Reset to factory defaults.
H-Series ballast, A-Series LED driver or
®
Note: Rapid Start sockets MUST
be used with EcoSystem ballasts.
®
H-Series, or Hi-lume 3D digital
®
White
(Neutral)
Black
(Hot)
To Ballasts
Note:
Use 18 to 16 AWG
(0.75 to 1.5 mm
E 1 solid wire only.
E 2
Link
on the PowPakR Dimming Module for 6 seconds to save
"
(consult individual component installation guides for
Reset Factory Defaults
Note: In some instances it may be necessary to
reset the PowPakR Dimming Module and
connected EcoSystemR devices back to
factory default settings. Before beginning,
make sure all devices are connected and
powered.
Triple-tap any button on the PowPakR
A
Dimming Module and hold until the
LEDs begin to flash slowly. (Release)
Within 3 seconds of the start of
B
flashing, triple-tap the same button
again and the LEDs will flash rapidly
indicating that the unit has been reset
to factory defaults.
Note: Any associations or programming previously
set up with the PowPakR will be erased and
will need to be re-programmed.
2 )
Test