Publicidad
Idiomas disponibles
Idiomas disponibles
3.
4.
Remove
two
screws
attaching
access
panel
and
lower
panel
to dishwasher
using
a 1/4" hex socket,
nut driver
or Phillips
screwdriver.
Remove
panels
and set panels
aside
on a protective
surface.
Check that grounding
clip is attached to the lower
panel.
lower
panel
clip
ApplyTeflon
_: tape
or pipe
joint
compound
to 90 ° elbow
fitting
and connect
fitting
to
water
inlet valve.
water
inlet valve
I
Tighten
elbow
until
snug,
and
be sure that
it faces
to the
rear.
7.
Remove
terminal
box
cover.
- If you are direct wiring:
install a U.L-listed/CSA-
certified clamp connector
to the terminal
box. If using
conduit,
use a U.L.-listed/CSA-certified
conduit
connector.
- If you
are installing
a power
supply
cord
kit, do so
now,
following
kit instructions.The
power
supply
cord
kit must
be U.L.-listed
and marked
for use with
dishwashers
(i.e. Power
Supply
Cord
Kit part
no. 4317824).
dishwasher wires
HelpfulTip:
Put cardboard
under
dishwasher
until
it is
installed
in cabinet
opening.The
cardboard
will
help
protect
floor
covering
during
installation.
Measure
height
of cabinet
opening
..............................................................................................
from
underside
of countertop
to
floor
where
dishwasher
will
be
installed
(you
need
the lowest
point).
Check chart
for that
height
opening.
Put wheels
in the
required
position.
wheel
_ '_/_
''_' / /
Number
of
Minimum
Wheel
turns on
cutout height
position
front leg
34" (86.4 crn)
1
10
34-1/4" (87 cm)
2
5
34-1/2" (8_6 crn)
3
0
9.
Turn
both
front
leveler
legs to the same
height.
If the minimum
cutout
height
is less than
34" (86.4 cm),
the rear wheels
can
be
removed
for additional
clearance.This
will
allow
the dishwasher
to fit into
a 33-7/8"
(86 cm)
high
cutout,
but the dishwasher
will
be more
difficult
to move
into
front leg
position.
If the wheels are removed,
protect the floor
when moving
the dishwasher.
if you have built-up
floors
2.
3.
Measure
height
of opening
from
underside
of
countertop
to built-up
floor.
If the height
is at
least
33-3/4"
(85.7 cm),
the
shim
_/
dishwasher
will fit into the
opening
without
modification
to the
countertop
or flooring.
/
countertop
33-3/4"
(85.7 crn)
rnin.
Put wheels
in position
1 and turn
the front
leveler
legs
up all the way.
Add
shims
as needed
in the area shown
to bring
dishwasher
up to proper
height.
NOTE:
Shims
must
be securely
attached
to floor
to
prevent
their
movement
when
the dishwasher
is
operated.
2"
(5.1 crn)
2-3/4"
6"
2-3/4"
(7.0cm)
(15.2 crn)
(Z0 cm)
Install
custom
door
panel
kit (on some models)
If installing
a custom
door
panel
kit, install
it now
following
instructions
included
with
kit.
Choose
attachment
option
Excessive
Weight
Hazard
Use two or more
people
to move
and install
dishwasher.
Failure
to do so can
result
in back
or other
injury.
Using
two
or more
people,
stand
the dishwasher
up.
Publicidad
