Publicidad
Idiomas disponibles
Idiomas disponibles
Option
2, No waste
disposer
- with
air gap:
1.
Cut end of drain
hose
if needed
(do not cut
ribbed
section).
2.
Attach
drain
hose
to air gap with
large
spring-type
clamp.
If the drain
hose
was
cut, use a 1-1/2"
to 2"
(3.8 to 5 cm) screw-type
clampL
3.
Use a rubber
hose
connector*
with
spring
or screw-
type
clamps*
to connect
air gap to waste
tee.
This
connection
must
be before
the drain
trap
and at
least 20" (50.8 cm) above
the floor
where
dishwasher
will
be installed.
drain hose-
_._
cut here if needed
spn_g or
rubber hose
connector
large
spring-type
drain
drain trap
hose
Insert drain hose through
hole cut in cabinet to the
front center of opening
where drain connection
will be made.
Parts available from local plumbing supply stores
Option
3, Waste disposer
- no air gap:
1. Remove the disposer
knockout
plug. Do not cut end of
drain hose.
Attach drain hose to disposer
inlet with large spring-
type clamp.
This connection
must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed, it is recommended
that the drain hose
be looped up and securely fastened
to the underside
of
the counter.
largespring-type
clamp
drain hose
disposer
inlet
drain trap
Insert drain hose
through
hole cut in
cabinet to the front
center of opening
where drain connection
will be made.
drain hose
Option
4, No waste
disposer
- no air gap:
1.
Cut end of drain
hose
if needed
(do not cut ribbed
section).
2. Attach
drain
hose
to waste
tee with
1-1/2" to 2"
(3.8 to 5 cm) screw-type
clampL
This connection
must
be before
the drain
trap
and at
least
20" (50.8 cm) above
the floor
where
dishwasher
will
be installed.
It is recommended
that
the drain
hose
be looped
up and securely
fastened
to the underside
of
the counter.
drain hose -
____
cut here if needed
__
screw-type clamp
waste _
tee
I
/_
I
.g_
_
_ _
_ra:en
dra,n trap
:-111
N
Insert drain hose
through
hole cut in
cabinet to the front
center of opening
where drain connection
will be made.
drain hose
r' Parts available from local plumbing supply stores
Prepare cabinet opening
where
there
are no existing
utility
hookups
Electrical
connection
Option1,
Direct
wire
method:
HelpfulTip:
Wiring
the dishwasher
will
be easier
if you
route
wire
into the cabinet
opening
from
the right
side.
1. Drill a 3/4" (1.9 cm)
hole in right-hand
cabinet side, rear or
floor. Preferred
and
optional
locations
are
shown.
2. Wood cabinet:
Sand
hole until smooth.
Metal cabinet: Cover
3.
4.
_optional
preferred [
ns
Ioc_
a UL listed/CSA
certified
conduit
connector
to the
junction
box.
Run other end of wire
through
cabinet hole.
Cable must extend to the
right front of cabinet
opening.
hole with grommet,
not provided.
Run wire into house wiring
junction
box.
Install a UL listed/CSA
certified
clamp connector
(strain
relief) for flexible-type
wire. If installing conduit,
attach
Publicidad
