Optional Accessories - Makita DCG180 Manual De Instrucciones

OPERATION
CAUTION:
• Do not touch the rod during operation.
Otherwise your finger may be pinched between
the rod and the housing of the tool.
• Always wear goggles during operation.
NOTICE:
• Do not cover vents, or it may cause overheating
and damage to the tool.
• If you can not pull out the rod, turn the speed
adjusting dial to 1, and pull the switch trigger for a
moment, and try to pull the rod out after the motor
stopped. If the rod is still clogged, perform the
same action until the rod is able to move.
Cut off the tip of the nozzle suitable for individual oper-
ation. Be careful how much you cut the nozzle. The
diameter of the nozzle affects the amount of caulking
material dispensed.
Pull the trigger to dispense caulking material.
The amount of the caulking material dispensed is
determined by the trigger, the speed adjusting dial, the
diameter of the nozzle opening, caulking material type,
and temperature.
It is recommended that the speed adjusting dial is set to
'1' and pull the trigger slowly at the first time to test how
much amount of caulking material is dispensed.
When the rod reaches front end, the motor starts idling.
Replace the caulking material when it happens.
NOTE: If the caulking material is not dispensed,
check the following items:
• Nozzle tip is not cut adequately. Cut the nozzle
tip suitable for individual operation.
• Hardened material gets clogged in the nozzle.
Remove the hardened material.
• The cartridge is damaged. Replace the
cartridge.
• Caulking material is stiff. Warm the material until
it becomes soft.
• The wrong piston is used. Use appropriate
piston.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before attempt-
ing to perform inspection or maintenance except
for the following troubleshooting related to the
light.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
• Clean the holder and the rod after every day's
work. Keep them free from the adhesive mate-
rial. Remove the caulking material before it
hardens. Remained adhesive material may
cause breakage of the tool.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Piston A
• Piston B
• Piston C
• Piston D
• Short holder (300ml(18.3cu.in)) set
• Long holder (600ml(36.6cu.in)) set
• Plate (If you have the big holder (800ml(48.8cu.
in)) only, and purchase the short holder
(300ml(18.3cu.in)) set or the long holder
(600ml(36.6cu.in)) set, the plate is also required.)
• Big holder (800ml(48.8cu.in)) set
• Nozzle
• Safety goggles
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the
most current warranty terms applicable to this product.
If annexed warranty sheet is not available, refer to the
warranty details set forth at below website for your
respective country.
United States of America: www.makitatools.com
Canada: www.makita.ca
Other countries: www.makita.com
10 ENGLISH