Publicidad
6. OPERATION
ES
Sanding
PT
FR
FR
FR
FR
The sander can be used for most sanding operations on materials such as wood, plastic,
11.
11.
11.
metal and painted surfaces.
IT
ES
ES
ES
ES
EL
PT
PT
PT
PT
PL
IT
IT
IT
IT
RU
Where possible, secure smaller workpiece to prevent them from moving under the sander.
EL
EL
EL
EL
Lower the sander in contact with the workpiece without pressure and then start the sander.
KZ
Move the sander slowly over the surface of the workpiece in a circular or curved motion with
PL
PL
PL
PL
an even, moderate pressure.
UA
If there are still scratches on your work after sanding, try either of the following:
RU
RU
RU
RU
- Go back to a coarser grit and sand the marks out before recommencing with the original
RO
choice or,
KZ
KZ
KZ
KZ
- Try using new sanding sheet of the same grit to eliminate the unwanted marks before
EN
UA
UA
UA
UA
7. MAINTENANCE
RO
RO
RO
RO
EN
EN
EN
EN
Disconnect from the power supply immediately if the supply cord is damaged. Take
care not to expose this tool to the rain.
(always replace the two brushes at the same time)
Cleaning
Avoid using solvents when cleaning plastic parts. Most plastic parts are susceptible to
damage from various types of commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, carbon dust, etc.
Eric LEMOINE
Eric LEMOINE
Eric LEMOINE
162
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
ADEO Services 135 Rue Carnot — CS 00001 59790 RONCHIN — France (
110
110
128
110
WARNING : Don't use this machine on plaster.
ADEO Services
ADEO Services
Wear safety goggles and dust mask.
135 rue Sadi Carnot
135 rue Sadi Carnot
135 rue Sadi Carnot
CS 00001
CS 00001
59790 Ronchin — France (
59790 Ronchin — France (
59790 Ronchin — France (
,
,
EC
EC
EC
,
,
,
EN 62841-1:2015
EN 62841-1:2015
Always disconnect the device before performing any adjustment or
EN 62841-2-4:2014
EN 62841-2-4:2014
maintenance operation. If the supply cord is damaged, it must be replaced by
EN 55014:2017
EN 55014:2017
the manufacturer or its service agent in order to avoid a hazard.
EN55014-2:2015
EN55014-2:2015
EN 61000-3-2:2014
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 61000-3-3:2013
EN 50581 :2012
EN 50581 :2012
: .
: .
: .
ADEO Services
CS 00001
)
)
,
:
:
:
300
300
300
300DS2.5
300DS2.5
300DS2.5
,
,
,
2006/42/EC
2006/42/EC
2006/42/EC
2014/30/EU
2014/30/EU
2011/65/EU
2011/65/EU
(EU) 2015/863
(EU) 2015/863
(EU) 2015/863
:
:
:
EN 62841-1:2015
EN 62841-2-4:2014
EN 55014:2017
EN55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581 :2012
.
.
.
CE: 19
CE: 19
CE: 19
Done in Ronchin : xx/xx/xxxx
Done in Ronchin : xx/xx/xxxx
Done in Ronchin : xx/xx/xxxx
)
:
:
:
2014/30/EU
2011/65/EU
)
)
)
Publicidad
