JB Systems DynaSpot Manual De Instrucciones página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

ENGLISH
Blackout Mode [BLMd]
Determines how the projector should react when no DMX-signal is detected.
 Press the MODE and UP/DOWN buttons until "BLMd" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to select one of the available blackout modes:
 [YES]: The unit will go in blackout mode as soon as no DMX is detected.
 [HOLd]: The unit stops moving and shows the output that corresponds to the last valid DMX-values.
 [SOUn]: The unit starts working in SOUND mode, based on the settings made in the setup menu.
 Once the right mode is shown on the display, press the ENTER button to select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Sound Sense [SOSE]
Used to set the sensitivity of the internal microphone
 Press the MODE and UP/DOWN buttons until "SOSE" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to choose a value between "00" (very low sensitivity) and "70" (high sensitivity).
 Once the right value is shown on the display, press the ENTER button select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Pan Inversion [IPAn]
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MODE and UP/DOWN buttons until "IPAn" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to select "OFF" (normal) or "On" (pan inversion) mode.
 Once the mode is selected, press the ENTER button to select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Tilt Inversion [ItLt]
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MODE and UP/DOWN buttons until "ItLt" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to choose "OFF" (normal) or "On" (tilt inversion) mode.
 Once the right mode is shown on the display, press the ENTER button to select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Led Display on/off [Led]
Switches the LED display automatically off or not.
 Press the MODE and UP/DOWN buttons until "Led" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP buttons to select "On" (display always lit) or "Off" (display dark when not used).
 Once the right mode is shown on the display, press the ENTER button to select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Display Rotation [dISP]
Rotate the display over 180° (upside-down) or not.
 Press the MODE and UP/DOWN buttons until the display shows "dISP".
 Press the ENTER button.
 Use DOWN and UP buttons to select "dISP" (normal display always lit) or "dSIP" (display upside-down).
 Once the right position is shown on the display, press the ENTER button to select it.
 Press the MODE button for about 2 seconds to store the setting and to return to running mode.
Auto Test [tESt]
Used to activate the internal "self-test" program which checks all possibilities of the unit.
 Press the MODE and UP/DOWN buttons until the display shows "tESt".
 Press the ENTER button to start the internal self-test program.
 To go back to the functions press the MODE button for about 2 seconds.
JB SYSTEMS
®
5/59
USER MANUAL
DYNASPOT

Publicidad

Tabla de contenido
loading

Tabla de contenido