SodaStream FIZZI Guia De Inicio Rapido página 9

TROUBLESHOOTING
Before you call for service, please check the list of problems and solutions below:
SPARKLING WATER MAKER DOES NOT CARBONATE:
You might be out of gas; replace your cylinder.
Ÿ
Cylinder may be loose. Remove the carbonating bottle, open and remove the back cover
Ÿ
to access the cylinder and retighten the cylinder by hand. DO NOT use tools. Apply firm
pressure but do not over tighten. If the cylinder is already firmly in place, it may be empty.
Replace with a full cylinder.
Check that the carbonating bottle has been filled up with water to the fill line.
Ÿ
Ensure that the Sparkling Water Maker is in the upright position.
Ÿ
CANNOT INSERT THE CARBONATING BOTTLE INTO THE SNAP-LOCK:
Pull the bottle rest towards you until it clicks into its fully forward position. Insert bottle
Ÿ
into Snap-Lock. Firmly push bottle up and back until it locks.
YOU HEAR GAS ESCAPING FROM THE CARBONATING BOTTLE:
The carbonating bottle may not be properly attached. Allow the Sparkling Water Maker to
Ÿ
finish the carbonation process and then you can detach the bottle and reconnect it. Follow
the instructions in the 'Create the Bubbles' section.
When carbonating, you should hear a puffing sound after the third press of the
Ÿ
carbonating button as well as after each additional press, which is the sound of pressure
being released.
It is normal to hear a small amount of gas released at the end of the carbonation process.
Ÿ
WANT TO RE-CARBONATE A DRINK THAT WAS ALREADY CARBONATED:
WARNING: FOR YOUR SAFETY, NEVER carbonate again after adding the flavor. You
Ÿ
may only recarbonate unflavored sparkling water.
YOUR SPARKLING WATER MAKER CONTINUES TO RELEASE GAS AFTER CARBONATION
IS FINISHED:
WARNING: Do not remove the cylinder or the bottle. Leave the Sparkling Water Maker
Ÿ
in an upright position. Do not touch it until you no longer hear gas escaping. When the
Sparkling Water Maker is no longer releasing gas, remove the carbonating bottle and
contact your local SodaStream Customer Service Center.
WARNING: In the event of a carbon dioxide leak, ventilate the area, breathe fresh air
Ÿ
and if feeling unwell seek immediate medical attention.
THE CARBONATING BOTTLE DOES NOT RELEASE ITSELF FROM THE SNAP-LOCK:
Gently pull the carbonating bottle towards you until it reaches its fully forward tilt position.
Ÿ
Never pull the carbonating bottle out of the Snap-Lock: always allow the bottle to release
itself. If the carbonating bottle does not immediately release from the Snap-Lock wait a
few moments and it may release. If it still does not release, then push the bottle back into
the vertical position and repeat the process to release it.
YOU HEAR THE SOUND OF LEAKING GAS AFTER INSTALLING A NEW CYLINDER
INTO THE SPARKLING WATER MAKER:
Screw the cylinder tighter into its fitting. DO NOT use tools.
Ÿ
YOU EXPERIENCE POOR CARBONATION:
WARNING: To prevent personal injury: DO NOT re-carbonate after adding flavor.
Ÿ
If you have not yet added flavor, carbonate again to a higher carbonation level.
Ÿ
Carbonate using cold water.
Ÿ
If you still experience poor carbonation you may be out of gas. Replace the cylinder.
Ÿ
WATER OVERFLOWS FROM THE CARBONATING BOTTLE DURING CARBONATION:
Check that the carbonating bottle is filled only to the fill line.
Ÿ
Verify that the carbonating bottle is firmly installed in the Snap-Lock. Check by gently
Ÿ
pulling the bottom of the bottle. If it feels loose, then remove and reinsert.
THE FLAVOR IN YOUR SPARKLING BEVERAGE IS NOT STRONG ENOUGH:
Just add more flavor to taste!
Ÿ
WARNING: To prevent personal injury: DO NOT re-carbonate after adding flavor.
Ÿ
SMALL PIECES OF ICE APPEAR IN THE WATER DURING CARBONATION:
This might happen when carbonating very cold water. If this happens, shorten the time of
Ÿ
each press until the ice stops appearing otherwise it can affect the carbonation. Any ice
created will simply melt.
Still having trouble?
Contact your local customer service representative by visiting www.sodastream.com
and selecting your country.