DeWalt DCS571 Manual De Instrucciones página 11

3. Place outer clamp washer
large flat surface against the blade with beveled side
facing out.
4. Thread blade clamping screw
hand (screw has left-hand threads and must be turned
counterclockwise to tighten).
5. Depress the blade lock button
the saw spindle with the blade wrench
counterclockwise until the blade lock engages and the
blade stops rotating.
6. Tighten the blade clamping screw firmly with the
blade wrench.
nOTE: Never engage the blade lock while saw is running,
or engage in an effort to stop the tool. Never turn the saw
on while the blade lock is engaged. Serious damage to your
saw will result.
To Replace the Blade (Fig. A, D)

WARNING: Remove battery before service,
adjustment, installing or removing accessories.
1. To loosen the blade clamping screw
blade lock button 12 and turn the saw spindle with
the blade wrench 14 until the blade lock engages and
the blade stops rotating. With the blade lock engaged,
turn the blade clamping screw clockwise with the
blade wrench (screw has left-hand threads and must be
turned clockwise to loosen).
2. Remove the blade clamping screw
washer 16 only. Remove old blade.
3. Clean any sawdust that may have accumulated in the
guard or clamp washer area and check the condition
and operation of the lower blade guard as previously
outlined. Do not lubricate this area.
4. Select the proper blade for the application (see
Blades). Always use blades that are the correct size
(diameter) with the proper size and shape center hole
for mounting on the saw spindle. Always assure that the
maximum recommended speed (rpm) on the saw blade
meets or exceeds the speed (rpm) of the saw.
5. Follow steps 2 through 6 under To Install the
Blade, making sure that the blade will rotate in the
proper direction.
Blades

CAUTION: Burn hazard. Do not touch the the blade
immediately after use. Contact with the blade may
result in personal injury.

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle
material. Foreign objects in the workpiece such as wire
or nails can cause tips to crack or break. Only operate
saw when proper saw blade guard is in place. Mount
blade securely in proper rotation before using, and
always use a clean, sharp blade.

WARNING: Do not cut ferrous and or non-ferrous
metals (steel), glass, masonry-type planking, or tile
with this saw.
16 on saw spindle with the
9 into saw spindle by
12 while turning
14
9 , depress the
9 and outer clamp
Do not use abrasive wheels or blades. A dull blade will
cause slow inefficient cutting, overload on the saw motor,
excessive splintering, and could increase the possibility of
kickback. Please refer to the table below to determine the
correct size replacement blade for your model saw.
Blade Diameter
DWA412TCT 4-1/2" (115 mm)
If you need assistance regarding blades, please call
1–800–4-D WALT (1–800–433–9258).
e
Installing the Belt Hook (Fig. E)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang
the tool from a work belt. DO NOT use the belt
hook for tethering or securing the tool to a person or
object during use. DO NOT suspend tool overhead or
suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt
hook , use only the screw
20
securely tighten the screw.
If the hook is not desired at all, it can be removed from
the tool.
Fig. E
20
Installing the Auxiliary Handle (Fig. A)
Using the supplied blade wrench
handle into place as shown in Figure A. The saw can be
13
used with or without the auxiliary handle in place.
Cutting Depth Adjustment (Fig. F)
1. Hold the saw firmly and loosen (counterclockwise) the
depth adjustment knob 5
desired depth of cut.
2. Make sure the depth adjustment knob has been
retightened (clockwise) before operating saw.
English
Teeth Application
24 Wood cutting
that is provided. Be sure to
21
21
screw the auxiliary
14
and move shoe to obtain the
9