Operating The Dishwasher - Bosch SHE6AP02UC/03 Manual De Instrucciones

Operating
SHE5AL
the Dishwasher
Child Lock Active Clean Sanitized Rinse Agent
_iiiiiiiiiiiii_
3h. 6h. 9h.
Half Load
Power -- Auto -- Regular-- Delicate -- Quick
Scrub Wash Wash Wash Wash
/iiiiiiiii_ _iiiiiii_ /_iiiiiiiiiiiiiii_ _ (iiiiiii_
Program Select
@ BOSCN
Delay
EcoSense
Start
b
To start the dishwasher:
• Door must be closed. Press the"ON/OFF' button.
• One of the Wash Cycle LEDs will be flashing. You can
now select a wash cycle.
• Press the "<" or ">" button to select the desired wash
cycle.
• Select the "Half Load" or "Delay Start" features if
desired at this point.
In addition to your Wash Cycle selection, for small loads of
lightly soiled dishes press the "Half Load" button. This will
save energy and water.
If you would like to delay the start time of the dishwasher
press the "DELAY" button until the desired delay time
(3,6,9 hrs.) is displayed by the corresponding LED.
• Press the "START" button to begin the cycle (Wash
Cycle Indicator Light will stop flashing)
• Press the "START" button (LED stops flashing)
NOTE: Rinse Agent Indicator Light will be illuminated if
the unit needs Rinse Agent.
Child Lock
• After pressing the "START" button you can activate
the Child Lock feature.
•
Press and hold down the "<" button until Child Lock
LED illuminates (Light goes out when button is
released).
• Now any button you press (except ON/OFF) will not
function and the Child Lock LED illuminates when
you press any button.
• To deactivate, press and hold the "<" button until the
Child Lock LED goes out.
To cancel a cycle:
• Press and hold the "START/RESET" button until the
"Active" LED goes out.
• Wait for about 1 minute until the dishwasher drains.
• Press the "ON/OFF" button.
• The "Clean" indicator light will illuminate.
• You are now ready to start a new cycle.
o
To enter the options mode(rinse agent setting, extra
dry heat, cycle completion signal):
• Door must be closed. Press the "ON/OFF" button to
turn the unit on.
• One of the Wash Cycle LEDs will be flashing.
• Press and hold down the ">" button, then press and
release the "START/RESET" button. Now release the
">" button.
• The "Clean" and one other LED will be flashing. You
are now in the options setup mode.
• Press ">" to select the option you would like to
adjust.
If the "Clean" and "Rinse Agent" LED are flashing you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized" LED are flashing you can set
the Extra Dry Heat.
To set the amount of Rinse Agent:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less
Rinse Agent.
Follow the prior instructions to enter "options" mode.
With the "Clean" and "Rinse Agent" LED flashing:
• Press the "<" button to change the amount of rinse
agent dispensed.
0 LEDs flashing --> Rinse Agent dispenser is OFF
1 LED flashing --> Lowest amount of rinse agent
2 LEDs flashing --> Medium amount dispensed
3 LEDs flashing --> Highest amount of rinse agent
• Press STARTto save your settings.
To turn Extra Dry Heat on or off:
With the "Clean" and "Sanitized" LED flashing:
• Press the "<" button to turn Extra Dry Heat on or off. 0
0 LEDs flashing --> Extra Dry Heat is OFF
1LED flashing --> Extra Dry Heat is ON
. Press START to save your settings.
19