General Power Tool Safety Warnings - Makita DFT023F Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening torque
No load speed (RPM)
Dimensions (L x W x H)
Rated voltage
Standard battery cartridge
Charger
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harm-
ful interference to radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference at his own expense.
SAFETY WARNINGS

General power tool safety warnings

WARNING:
Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive atmo-
2.
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a
3.
power tool. Distractions can cause you to lose control.
Electrical Safety
Power tool plugs must match the outlet. Never
1.
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Hard joint
Soft joint
with BL1415NA battery
with BL1430 battery
DFT023F
0.5 - 2 N•m (4 - 18 in•lbs)
0.5 - 2 N•m (4 - 18 in•lbs)
400 - 1,300 /min
159 mm (6-1/4") x 72 mm (2-13/16") x 232 mm (9-1/8")
159 mm (6-1/4") x 72 mm (2-13/16") x 249 mm (9-3/4")
BL1415NA, BL1430, BL1430B, BL1460A
DC18RC, DC18RD, DC18SD, DC18SE, DC18SF
1.1 - 1.3 kg (2.4 - 2.9 lbs)
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
Personal Safety
Stay alert, watch what you are doing and use
1.
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
2 ENGLISH
DFT045F
1 - 4 N•m (9 - 35 in•lbs)
1 - 4 N•m (9 - 35 in•lbs)
150 - 900 /min
D.C. 14.4 V