Tubular Motor Installation; Installation In The Winding Shaft (Round Tube) - Nice ERA XL Instrucciones Y Advertencias Para La Instalación Y El Uso

Lifting capacity chart (kg) for one-piece roller shutters and rolling doors
Type Rated Shaft Ø
torque
Nm mm
100
100
100
120/12 120
133
133
133
100
100
100
150/12 150
133
133
133
100
100
100
180/12 180
133
133
133
100
100
100
230/12 230
133
133
133
100
100
100
300/12 300
133
133
133
The stated figures refer to the complete roller shutter / rolling door in kg.
15% friction is taken into account. The friction can be higher due to additional door seals, wind loads etc. Carry out nec-
essary corrections.
4 – English
Nom. bar Rolling door / roller shutter height up to
thickness
2.0 m 2.5 m 3.0 m
mm kg kg kg
14 182 175 168
19 167 160 150
23 157 151 140
14 146 146 142
19 143 138 133
23 139 131 126
14 227 218 210
19 209 200 188
23 196 188 174
14 182 182 178
19 179 172 166
23 173 164 158
14 272 262 251
19 251 241 226
23 236 226 209
14 219 219 213
19 215 206 199
23 208 196 189
14 384 335 321
19 320 307 288
23 301 289 267
14 279 279 273
19 274 264 255
23 265 251 242
14 454 436 419
19 418 401 376
23 393 377 349
14 364 364 356
19 358 344 332
23 346 327 315
3.5 m 4.0 m 4.5 m 5.0 m
kg kg kg kg
160 155 149 143
143 138 132 126
132 127 122 116
139 136 133 129
130 125 121 117
123 117 113 109
200 193 186 179
179 172 165 158
165 159 152 145
174 171 166 161
162 156 151 146
154 146 141 137
240 232 223 215
214 207 198 190
198 191 183 223
208 205 199 194
194 188 181 176
185 176 169 164
306 296 285 275
274 264 253 242
253 244 234 223
266 261 254 247
248 240 231 224
236 224 216 203
400 386 372 358
357 344 330 316
330 318 305 291
347 341 331 323
324 313 301 293
308 293 281 273

3.2 - Tubular motor installation

Caution!
• The fitter has to check the solidity of the masonry etc.
before installing the system.
• The fixing plates of the ERA XL and ERA XLH tubular mo-
tors are not oscillating and must be attached at right an-
gles without tension to the fixing area.
• It is imperative to use the wall bracket plate item no.
537.10001 in case of unevenness.
3.2.1 - Installation in the winding shaft
(round tube)
01. Cut a notch into the tube on the motor side.
b
Tube Ø a b Tube Ø
(mm) (mm) (mm) (mm)
98 x 2 8,5 28 133 x XX
100 x 3 8,5 28 159 x XX
102 x 2 14,5 31 168,3 x XX
108 x 3,6 14,5 31
02. Place the drilling template around the tube according
to the table of dimensions on page 6 and adhere it.
Subsequently mark with a punch.
03. Drill using a 8.5 mm Ø drill bit, then make the recess
for the countersink screw head.
04. Push the drive with matching drive adapter and limit
switch crown into the tube, as well as the limit switch
crown cam into the slot.
Do not knock or let the drive fall into the tube.
a b
(mm) (mm)
8,5 28
12,5 26
12,5 26