Black and Decker LCS1020 Manual De Instrucciones página 6

• Normal Cutting
Position - Those
positions assumed in
_erforming the bucking and felling cuts.
otching Undercut - A notch cut in a
tree that directs the tree's fall.
• Rear Handle - The support handle
located at or toward the rear of the saw.
• Reduced Kickback Guide Bar - A guide
bar which has been demonstrated to
reduce kickback significantly.
• Replacement Saw Chain - A chain that
complies with kickback performance
requirements of ANSI B175.1-2000 when
tested with specific chain saws. It may
not meet the ANSI performance
requirements when used with other saws.
Saw Chain - A loop of chain having
cutting teeth, that cut the wood,andthat is
driven by the motor and is supported by
the guide bar.
• Ribbed Bumper - The ribs used when
felling or bucking to pivot the saw and
maintain position while sawing.
• Switch - A device that when operated will
complete or interrupt an electrical power
circuit to the motor of the chain saw.
• Switch Linkage - The mechanism that
transmits motion from a trigger to the switch.
• Switch Lockout - A movable stop that
prevents the unintentional operation of
the switch until manually actuated.
INTENDED USE
Your BLACK+DECKER Chain Saw is ideal
for pruning applications and cutting small
logs up to 10 inches (254 mm) for the
LCS1020 and up to 12 inches (305 mm)
for the LCS1240 in diameter. This tool is
intended for consumer use only.
SAVE THESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V.................. volts
A .................. amperes
Hz ................ hertz
W. ................ watts
min .............. minutes
"_ or AC ...... alternating current
- - -or DC...direct current
no ................ no load speed
@ ................ Class I Construction
(grounded)
0 ................ earthing terminal
................ safety alert symbol
[] ................ Class II Construction
(double insulated)
.../min or rpm...revolutions or
reciprocation per minute
m/s .............. meters per second
in ................. inches
mm .............. millimeters
_. ............... Read instruction manual
before use
................ Use proper respiratory
protection
_ ................ Use proper eye protection
® ................ Use proper hearing
protection
.... .............. Rotational direction of the
saw chain
............... Contactof theguidebar tip with
any objectshouldbe avoided
_ ................ Tip contactcan causethe guide
bar to move suddenlyupwardand
backward,whichcan cause
seriousinjury
_ ........... Always use two hands when
operating the chain saw
IMPORTANT SAFETY
iNSTRUCTiONS FOR BATTERY
CHARGERS
SAVE THESE INSTRUCTIONS: THiS
MANUAL CONTAINS iMPORTANT
SAFETY iNSTRUCTiONS FOR
BATTERY CHARGERS.
• Before using charger, read all instructions
and cautionary markings on charger, battery
pack, and product using battery pack.
ZLWARNING:
SHOCK HAZARD. Do
not allow any liquid to get inside charger.
ZLWARNING: BURNHAZARD. T o
reduce the risk of injury, charge only
designated BLACK+DECKER batteries.
Other types of batteries may burst causing
personal injury and damage.
z_CAUTION:
Under certain
conditions,
with the charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of a
conductive nature such as, but not limited
to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when there
is no battery pack in the cavity. Unplug
charger before attempting to clean.
zLWARNING:
The
chargersupplied
with this product is intended to be plugged
in such that it is correctly orientated in a
vertical or floor mount position,
• DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and
battery pack are specifically designed to
work together.
• These chargers are not intended
for any uses other than charging
designated Black+Decker rechargeable
batteries. Any other uses may result in
risk of fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce
risk of damage to electric plug and cord.