Setup Menu; Delete Chase; Erase Memory - JB Systems LED DIRECTOR Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

ENGLISH

SETUP MENU

The setup menu is used to configure the LED Director and perform some less used functions. Press the
MENU button (4) for about 1 second to enter the setup menu. The menu contains 11 sections that are fully
explained below:
1/ SET DATE
 Use the dial (14) to select "SET DATE" and
press the ENTER button (13)  the display
shows the current date.
 Use the dial (14) to select the item you
want to edit (year, month or day will be
underlined)
 Press ENTER (13) and use the dial (14) to
adapt the value
 Press ENTER (13) to confirm and also
adapt the other values.
 Turn the dial (14) until the display shows
"STORE DATE SET"
 Press ENTER (13) to confirm.
Note: if you want to return to the main menu,
just press the MENU button (4) shortly.
2/ SET TIME
 Use the dial (14) to select "SET TIME" and
press the ENTER button (13)  the display
shows the current time.
 Use the dial (14) to select the item you
want to edit (hours, minutes or seconds will
be underlined)
 Press ENTER (13) and use the dial (14) to
adapt the value
 Press ENTER (13) to confirm and also
adapt the other values.
 Turn the dial (14) until the display shows
"STORE TIME SET"
 Press ENTER (13) to confirm.
Note: if you want to return to the main menu,
just press the MENU button (4) shortly.
3/ SET CLOCK
Here you can set the start/stop times for up to
21 timed chases (3 chases/day x 7 days = 21
timers)
Note: while programming a timer, just press
the MENU button (4) shortly, if you want to go
to the previous step(s) and correct it.
 Use the dial (14) to select "SET CLOCK" and press the ENTER button (13)  the display shows "CLOCK
SET: SUN". (SUN = Sunday)
 Use the dial (14) to select the day you want. (in this example we choose MON "Monday")
 Press ENTER (13) to confirm  the display shows "CLOCK MON: x" (x = the number of the timer)
 Use the dial (14) to select the timer you want to edit. (in this example we choose 2 "timer 2")
 Press ENTER (13) to confirm  the display shows "ON: MON hr:min:sec" (start time of the chase timer)
 Use the dial (14) to select the item you want to edit (hours, minutes or seconds will be underlined)
 Press ENTER (13) and use the dial (14) to adapt the value.
 Press ENTER (13) to confirm and also adapt the other values.
 Turn the dial (14) until the display shows "OFF: FRI hr:min:sec" (stop time of the chase timer)
 Use the dial (14) to select the item you want to edit (day, hours, minutes or seconds will be underlined)
JB SYSTEMS
®
OPERATION MANUAL
5/50
LED DIRECTOR
ENGLISH
 Press ENTER (13) and use the dial (14) to adapt the value
 Press ENTER (13) to confirm and also adapt the other values.
 Turn the dial (14) until the display shows "CHASE [01]" (number of the chase you want to select)
 Press ENTER (13) and use the dial (14) to adapt the value
 Press ENTER (13) to confirm
 Turn the dial (14) until the display shows "CLOCK [OFF]"
 ATTENTION!!! CLOCK [OFF] means that the timer is programmed but NOT activated!!!
 Press ENTER (13) and use the dial (14) to change it to "CLOCK [ON]"
 Press ENTER (13) to confirm
 Turn the dial (14) until the display shows "STORE MON2 SET" (in our example!)
 Press ENTER (13) to confirm (yellow and green LED blink 3times)
The display shows "CLOCK SUN:2" (in our example!)
you can start the procedure again to program a new timer OR press 2x the MENU button (4) to return to
the main menu.

4/ DELETE CHASE

 Use the dial (14) to select "DELETE CHASE" and press the ENTER button (13)  the display shows
"DELETE Chase: 01".
 Use the dial (14) to select the chase you want to delete
 Press ENTER (13) to confirm  the display shows "DELETE? [NO]"
 Use the dial (14) to change it to "DELETE? [YES]"
 Press ENTER (13) to confirm (yellow and green LED blink 3times)
you can start the procedure again to program a new timer OR press the MENU button (4) to return to the
main menu.
5/ CHASE BY TIME
This option determines how the parameters "fade time" and "wait time" influence the timing of the
programmed chase during playback. We suggest to think about this before you start programming the
chases, since it influences the final result a lot. Two options are available:
 RUN TIME BY CHASE: This is the easiest method but with less possibilities. The parameters "fade
time" and "wait time" are set during playback. This means that all steps of the chases will have the same
fade and wait times.
 RUN TIME BY SCENE: This method gives you the possibility to enter a different fade and wait time for
every scene of a chase! This means that you can change the playback & color fade speeds to obtain a
very dynamic chase. However, during playback you can't change these parameters anymore!
Select as explained below:
 Use the dial (14) to select "CHASE BY TIME" and press the ENTER button (13)  the display shows
"RUN TIME BY CHASE" or "RUN TIME BY SCENE".
 Use the dial (14) to select the option you want.
 Press ENTER (13) to confirm (yellow and green LED blink 3times)

6/ ERASE MEMORY

Be VERY careful with this one: the complete memory will be erased!
 Use the dial (14) to select "ERASE MEMORY" and press the ENTER button (13)  the display shows
"ERASE? [NO]".
 Use the dial (14) to change it to "ERASE? [YES]"
 Press ENTER (13) to confirm  the display shows "Please Wait ... " followed by the yellow and green
LEDs blinking 3times.
Note: if you want to return to the main menu, just press the MENU button (4) shortly.
7/ LOCK KEYBOARD
This option locks the keyboard so unauthorized persons can't use it. In the setup menu you can enable the
locking feature however you still have to perform additional actions to really LOCK the keyboard!
 Use the dial (14) to select "LOCK KEYBOARD" and press the ENTER button (13)  the display shows
"LOCK ENABLE" or "LOCK DISABLE".
 Use the dial (14) to select the option you want.
 Press ENTER (13) to confirm (yellow and green LED blink 3times)
JB SYSTEMS
®
OPERATION MANUAL
6/50
LED DIRECTOR

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

B04938

Tabla de contenido