Quick ARIES Serie Manual Del Usuario página 17

16A Chain guide cover A
16B Chain guide cover white F
16C Chain guide cover black F
17A Screw Aries base
17B Screw Flair base
18A Rope/chain stripper Aries base
18B Rope/chain stripper Flair base
19 Sensor
20 Screw for pressure lever
21A Black pressure lever
21B White pressure lever
22 Spring for gypsy pressure lever
23 Cover pin
24A Oval base Aries
24B Oval base white Flair
24C Oval base black Flair
25 Base Rider
26 Rope/chain stripper R base
27 Screw Rider base
28 Gasket/A-F - shaped jig
29 Gasket/R - shaped jig
30 Stud
31 Gearbox flange gasket
Top TG50
32 Gearbox flange gasket
Top TG60
33 Gearbox 700/1000W Quick
34 Gearbox 1400W Quick
35 Washer
36 Spring washer
37 Nut
38 Washer
39 Self locking nuts
40 O-ring motorgearbox
700/1000/1400W
41 Key 5x5x15
42A Electric motor 700W 12V
42B Electric motor 700W 24V
42C Electric motor 1000W 12V
42D Electric motor 1000W 24V
42E Electric motor 1400W 12V
42F Electric motor 1400W 24V
43A Watertight 700W
43B Watertight 1000/1400W
44 Grommet
45 Terminal board cover
46 Screw
47 Bottom gasket
48 Bottom protec cover
49 Cable outlet
50 O-ring 3125
AFR 700/1000/1400W - REV012A
SGMSGG100000
PDGC10DW0000
PDGC10DB0000
MBV0516MXSC0
Quick
MBV0530MXSC0
marine environments. In any case, any salt deposits on the outside
MSN10VXP0000 must be removed periodically to avoid corrosion and damage to
the equipment. The parts where salt may have built up should be
MSN10VXD0000
washed thoroughly with fresh water.
SAKREED00000
MSMVT1000000
Once a year, the drum and the gypsy are to be taken apart as fol-
PDLVTD100000
lows:
PDLVTD10W000
MMTND1000000
DRUM VERSION
MSR10X000000
Use the handle (1) to loosen the bush (3); pull off the drum (4) and
SGMSC10V0000
the top clutch cone (5); loosen the fixing screws (17 or 27) of the
SMPD10VW0000
rope/chain stripper (18 or 26) and remove it. Pull off the gypsy (6).
SMPD10VB0000
SGMSC10C0000
NO-DRUM VERSION
MSN10CX00000
Use the handle (1) to remove the gypsy cover (2); remove the top
MBV0620MXSC0
clutch cone (5); loosen the fixing screws (17 or 27) of the rope/chain
PGBSV1000000
stripper (18 or 26) and remove it and pull off the gypsy (6).
PGBSC1000000
MBP080808X00
Clean all the parts removed to avoid corrosion, and grease the shaft
thread (13 and 14) and the gypsy (6) where the clutch cones (5) rest
PGFLRDTG50000
(use grease suitable for marine environment) .
PGFLRDTG60000
Periodically grease the hinge pin (23) of the chain guide cover (16)
SLMR10TG5000
(only windlasses with aluminium bases).
SLMR15TG7000
MBR08X000000
Remove any oxide deposits from the terminals of the electric motor
MBR08XDE0000
and the contactor unit; grease them.
MBD08MXEN000
MBR061815X00
MBD06MXET000
PGR023000000
MBH050515F00
EMF071200000
EMF072400000
EMF101200000
EMF102400000
EMF141200000
EMF142400000
PCCCPM070000
PCCCPM100000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
PGR031650000
MAINTENANCE
WARNING: make sure the electrical power to the motor
is switched off when working manually on the windlass.
Carefully remove the chain or rope from the gypsy or the
rope from the drum.
® windlasses are manufactured with materials resistant to
GB
17