Oscartielle PLANET 2 Instrucciones De Uso página 14

ENGLISH
1 - Description of cabinet
The PLANET 2 – PULSAR 2 range of display units are built in modules with a useful internal length of 520 mm (MODEL
58), 620 mm (MODEL 70), 1060 mm (MODEL 112). They are equipped with an integral condensing unit, with fan assisted
refrigeration. FIG. 1 on page 1 clearly shows the general look and dimensions of these units.
2 - Transport of the unit
The cabinet is provided with wooden runners (wooden crating available on request) so as to be movable by means of a
forklift. The handling should only be done by authorized personnel.
The weight of the unit and insertion points of the forks for handling are shown in FIG.2 and TAB. 1 on page 1.
3 - Arrival and storage
On delivery, make sure the cabinet has not been damaged and check the conditions of the packing. If it shows any
damage, check the contents in the presence of the carrier. The cabinet should be protected from atmospheric agents and
stored at a temperature between -25°C and +55°C, with relative humidity between 30% and 95%.
The unit must be unpacked with care because the packing contains some parts and/or accessories required to complete
the island (Spacers, etc.).
Disconnect the cabinet from the fastening brackets (FIG. 3 page 2) and remove the white padding around it. Position the
cabinet exactly where you plan to install it. Move the cabinet carefully, never pull it by the side glasses!
Important: if the goods are delivered damaged, notify the manufacturer at once: any delay in reporting damage will
relieve the manufacturer of all liability.
Any damage to the cabinet occurring during shipment and storage may not be attributed to the manufacturer.
4 - Installation and environmental conditions
For correct operation, make sure the cabinet is absolutely level and, if necessary, adjust it by screwing or unscrewing the
feet (FIG. 4 page 2).
Do not install the cabinet in rooms where there are explosive gasses.
Do not use the cabinet out of doors or expose it to rain (FIG. 5 page 2).
The performance of the cabinet refers (according to the international standard EN ISO 23953-1/2) to environmental
climatic class 3 which consists of a room temperature of 25°C with relative humidity of 60%.
Sufficient space must be provided to guarantee good air circulation for the condenser (FIG. 6 page 2). The presence of
objects in front of the protection grid of the condenser do not allow the cabinet to work properly (FIG. 7 page 2).
If the environmental conditions are different, or the cabinets are exposed to drafts in excess of 0.2m/sec., or heat
radiations, the user must accept inferior performance.
To avoid this problem, the User should send the Manufacturer details of the environmental conditions before finalising the
design of the units, so that the technical parameters and material options can be modified and the installer be informed of
the refrigerating power actually required.
5 - Electric connection
Important: installation should be made following the manufacturer's instructions, by qualified personnel only, in conformity
with the electric safety regulations in force. Please refer to the electrical diagram at page 5 FIG.13.
At the input of the supply it is necessary to install an omni-polar magnetothermic/differential device with contact opening
equal to 3 mm and adequate cut-off power.
Caution: Before connecting the cabinet to the power mains make sure the supply voltage corresponds to the rating on
the serial number plate (consider that the maximum voltage variations admissible are +/-10%). Make sure the electric
connection is made with cables of a diameter and length capable of withstanding the power and current absorbed by the
display cabinet (please refer to page 3, TAB. 2).
Cabinets with incorporated compressor are supplied with a cable and plug 2,5 m. long (FIG. 8 page 3) therefore it is
essential not to exceed this measure in connecting the cabinet to the wall socket. The cable should be fully extended in a
safe position away from possible impact and at a distance from liquids or water and heat sources. In case of breakage of
the power cable of the cabinet, it must be replaced by the manufacturer or by institution in charge of it. The plug should
be accessible even after installation of the cabinet.
The display (FIG. 9 page 3) on the front shows the working temperature of the unit. The instruction manual for the
electronic control to which the display refers is enclosed with the instruction booklet (tampering with this device is
impossible because a password is required and only a specialized expert can modify it). The thermostat and gas charge
are set in the factory. Tampering with the factory settings relieves the manufacturer of any liability.
Important: installation should be made following the manufacturer's instructions, by qualified personnel in conformity with
the electric safety regulations in force in the country where the cabinet is installed (electric safety regulations and laws,
accident prevention laws, fire prevention regulations, directives).
Always ground the cabinet. The manufacturer is not liable for any injuries caused by failure to respect this regulation.
If there is no wall socket near where the cabinet is to be installed, provide for connection in conformity with the regulations
in force. Do not use adapter plugs.
The manufacturer has no liability for any damage to personnel or property caused by improper installation.
12