Starting Operation - Bosch PSM VENTARO 1400 Instrucciones De Servicio

OBJ_BUCH-2 609 932 412-001.book Page 5 Thursday, January 13, 2005 12:48 PM
Specialty Sanding Plates
You can replace the supplied sanding plate 24 with a
specialty sanding plate, which is available as an acces-
sory.
The specialty sanding plate is attached in the same
manner as the one supplied.
Attach and remove the respective sanding sheets in the
same manner as when changing original sanding
sheets.
Pad Extender (see figure I)
With the pad extender 26 you can sand surfaces that
are difficult to access, such as sills on windows, cabi-
nets or doors.
Pad Extender, Narrow (see figure J)
With the narrow pad extender 28 you can sand narrow
openings, slots and passages.
Pad Extender, Narrow Rounded (see figure K)
The narrow rounded pad extender 29 allows you to
sand curved and hollow areas or surfaces that are
curved inward, such as on furniture, rails or heating
radiators.
Operation

Starting Operation

Observe the correct mains voltage! The voltage of
the power source must agree with the voltage specified
on the nameplate of the vacuum cleaner. Vacuum
cleaners marked with 230 V can also be connected to
220 V.
Switching On and Off
B Switch the vacuum cleaner on when the
sander is set at "0". After switching off, wait
until the sander has come to a standstill
before placing it down. The sander can move
unintentionally.
B Completely unreel the cable before putting
the vacuum cleaner into operation. The cable
can heat up.
B Before using the vacuum cleaner, always
remove the plug cap 9. Pay attention that the
bypass valve 15 is never restricted or blocked.
The motor of the vacuum cleaner can overheat und
become damaged.
2 609 932 412 • 13.1.05
To start the vacuum cleaner, press the On/Off
switch 7.
To switch the vacuum cleaner off, press the On/Off
switch 7 again.
When putting the multi sander into operation, start
the vacuum cleaner first and then push the On/Off
switch of the sander 2 toward the front to position "I".
Press the On/Off switch 2 downward to lock it in this
position.
To switch off the multi sander, first push the On/Off
switch 2 of the sander to the rear to position "0" and
then switch off the vacuum cleaner.
Operating Instructions
B Keep the blower opening unrestricted and do
not crease or bend the vacuum hose. The motor
can overheat.
Insert the plug cap for the vacuum hose connection 9
into the vacuum hose connection 8 when not using the
vacuum cleaner for longer periods.
Working with the Multi Sander
The removal capacity during sanding is mainly deter-
mined by the selection of the sanding sheet.
Only flawless sanding sheets achieve good sanding
capacity and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an
increase of the sanding capacity, but to increased wear
of the machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and
hard to reach areas, it is also possible to work only with
the tip or an edge of the sanding plate.
A sanding sheet that has been used for metal should
not be used for other materials.
To eliminate the hazard of fires, replace the dust bag in
the vacuum cleaner before sanding metals.
Use only original Bosch sanding accessories.
Using the Drilling Helper (see figure D)
The drilling helper 19 enables dust-free drilling in walls
etc. to the greatest extent.
Insert the vacuum hose 3 with the extraction adapter 20
mounted into the connection of the drilling helper 19.
Switch on the vacuum cleaner and position the drilling
helper 19 against the wall in such a manner that the
hole of the drilling helper is flush with the hole to be
drilled. Due to the vacuum, the drilling helper remains
attached to level surfaces without requiring further
aides.
English–5