Directions For Use - PPS 3M Manual De Instrucciones

Directions for Use:

• Requires the use of a 3M™ PPS™ Series 2.0 spray gun adapter (sold separately) to attach the
3M™ PPS™ Series 2.0 Type H/O Pressure Cup to the spray gun. Reference Figure 1.
• Optional use of 3M™ PPS™ Mix Ratio Film Insert PN 16091 (Large), PN 16155 (Midi), sold
separately.
• Requires the use of 3M™ PPS™ Series 2.0 H/O Lids (PN 26150 - Large/Standard; PN 26151 Midi/
Mini) and Series 2.0 Liners (PN 16351 - Large; PN 16350 - Standard; PN 16349 - Midi; PN 26348 -
Mini), sold separately, to contain the material to be sprayed.
• Requires an operating pressure of ≤ 10 psi (69 kPa, 0.69 Bar) to the 3M™ PPS™ Series 2.0
Type H/O Pressure Cup. The 3M™ PPS™ Series 2.0 Type H/O Pressure Cup contains a built in
"pressure relief valve" located in the base of the cup to avoid over pressurizing. If the pressure
relief valve is damaged, the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup must be replaced.
• Use Only Genuine 3M Parts and Accessories. Reference Figure 2 Component Listing.
Setup Sequence:
1. Insert optional 3M™ PPS™ Mix Ratio Film Insert (3) into the 3M™ PPS™ Series 2.0 Type H/O Pressure
Cup (1) if desired. Otherwise, insert a 3M™ PPS™ Liner (4) into the 3M™ PPS™ Series 2.0 Type H/O
Pressure Cup (1) and add the desired amount of material to be sprayed.
2. Insert a 3M™ PPS™ Series 2.0 H/O Lid (5) onto the 3M™ PPS™ Liner (4) and press down until secured.
3. Align the opening on the Retaining Collar Shroud Assembly (6) with the 3M™ PPS™ Series 2.0 H/O Lid and
screw the Retaining Collar clockwise onto the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (1) and hand-
tighten.
4. If the material will not be sprayed immediately, a 3M™ PPS™ Series 2.0 Plug (7) can be inserted into the
lid spout to seal contents.
5. When ready to spray the contents, remove 3M™ PPS™ Series 2.0 Plug (7) if used, and connect the spray
gun with the previously installed 3M™ PPS™ Series 2.0 Adapter to the 3M™ PPS™ Series 2.0 Type H/O
Pressure Cup. Reference Figure 1.
a. While aligning the 3M™ PPS™ Series 2.0 Adapter with the 3M™ PPS™ Series 2.0 H/O Lid and the 3M™
PPS™ Series 2.0 Retaining Collar Shroud Assembly, press down to fully seat and then turn gun 1/4 turn
clockwise, ensuring all 4 connection points engage.
6. Attach the cup pressure hose (2) from the spray gun to the pressure port (1b) on the 3M™ PPS™ Series
2.0 Type H/O Pressure Cup. The hose clip on the cup (1a) may be used to hold the hose securely in place
while spraying, hose clip included in 3M™ PPS™ Series 2.0 Type H/O Pressure Cup (Large) only.
7. Connect the spray gun to the air supply.
8. With the spray gun and the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup held perpendicular to the
ground, pull the trigger and adjust to the desired cup pressure, not to exceed a maximum operating
pressure of 10 psi (69 kPa, 0.69 Bar). Caution: Pressure relief valve (1c) at the base of the cup will
open at 30 psi (207 kPa, 2.07 Bar) and relieve excess pressure. The relief valve will close and reset
when the cup pressure is reduced. Keep trigger pulled until air from inside the 3M™ PPS™ Lid and Liner
has been totally evacuated and a steady spray of material is coming from the spray-head of the gun. This
will allow the gun to be held and sprayed upside down without fluid interruption.
9. Spray materials normally, periodically check the pressure to the cup to ensure pressure does not exceed
maximum operating pressure.
10. When done spraying, disconnect the input air supply from the spray gun.
11. Attention: Before disassembling the gun from the cup, the pressure must be relieved by
disconnecting the cup pressure hose at the base of the cup (1b).
12. While holding the spray gun upright for a bottom fed spray gun or turning the spray gun gun over for a
gravity fed spray gun. Pull the trigger to allow any remaining material to drain out of the fluid passage in the
spray gun and 3M™ PPS™ Series 2.0 Adapter back into the 3M™ PPS™ Liner:
Attention: Failure to do so will result in a material spill on the 3M™ PPS™ Series 2.0 Retaining
Collar Shroud Assembly.
13. Disconnect the 3M™ PPS™ Series 2.0 Type H/O Pressure Cup from the spray gun at the 3M™ PPS™
Series 2.0 Adapter by turning the gun counter-clockwise slightly to disengage locking tabs and pull gun
upwards to separate from the cup assembly.
English - 3