Care And Maintenance - Kärcher FC 5 Manual De Uso

Turning Off the Appliance
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Place the appliance in the cleaning station.
Illustration
ATTENTION
After completing the work, clean the appliance by apply-
ing a rinse cycle.
See "Cleaning the appliance by rinsing".
Illustration
 Completely empty the appliance.
Illustration
until
Illustration
 Empty the waste water tank.
See Chapter "Emptying the waste water tank".
 If there is still water in the fresh water tank or clean-
ing station, empty it.
Illustration
 Disconnect the main plug from the socket.
Illustration
 Wind the mains cable around the cable clips.
 Secure the mains cable with the cable clip.
Storing the Appliance
ATTENTION
To prevent odours developing, the fresh water and
waste water tank must be completely emptied prior to
storing the appliance.
Illustration
 Move the appliance to the place of storage using
the carrying handle.
Illustration
 To stabilise, place the appliance into the cleaning
station.
 Store the appliance in a dry room.

Care and maintenance

Cleaning appliance with rinsing process
ATTENTION
When the work is finished, always rinse the appliance
through with the cleaning station and fresh water. This
is the best way of cleaning the appliance. It prevents the
build-up of dirt and bacteria or unpleasant odours.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Place the appliance in the cleaning station.
 If there is still water in the fresh water tank, remove
the fresh water tank and empty it.
 Insert the fresh water container into the appliance.
Illustration
 Remove the waste water tank and empty it.
See Chapter "Emptying the waste water tank".
 Fill the measuring cup with 200 ml water.
 Fill the cleaning station with water.
 If necessary, add appropriate KÄRCHER cleaning
agents for the rinsing procedure.
 To switch on the appliance press the on/off switch.
 Allow the appliance to run for 30-60 seconds until
the water is completely drawn out of the cleaning
station.
10
The rinsing procedure is now complete.
Note
The longer the appliance is switched on, the less resid-
ual moisture is left over in the cleaning rollers.
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Empty the waste water tank.
See Chapter "Emptying the waste water tank".
 If there is still water in the fresh cleaning station,
empty it.
Illustration
 Disconnect the main plug from the socket.
Illustration
 Wind the mains cable around the cable clips.
 Secure the mains cable with the cable clip.
Cleaning the rollers
ATTENTION
The fresh and waste water tanks must be emptied be-
fore the appliance is set down on the ground for roller
removal. This prevents any fluids from leaking out of the
tank when it is laid on the ground.
Note
In the case of heavy contamination, clean the cleaning
rollers separately.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Disconnect the main plug from the socket.
 Empty the fresh water reservoir.
Illustration
 Empty the waste water tank.
Illustration
 Twist out the cleaning rollers from the recessed
grip.
 Clean the cleaning rollers under running water.
or
 Wash the cleaning rollers in the washing machine
up to 60°C.
ATTENTION
Do not use any soft detergents when cleaning in the
washing machine. This avoids causing damage to the
microfibres. It also preserves the high performance lev-
els of the cleaning rollers.
The cleaning rollers are not suitable for the tumble dry-
er.
 After cleaning, allow the rollers to air-dry.
Illustration
 Screw the cleaning rollers onto the threaded rod up
to the mechanical stop.
 Pay attention to the colour-codes on the inside of
the roller and roller holder on the appliance (e.g.
blue should match up with blue).
 After the installation, check to ensure that the
cleaning rollers sit snugly.
– 10
EN