Publicidad
GB
Fejl
Hvis rundsaven ikke virker hensigtsmæssigt, kan du gennemgå følgende mulige årsager og
D
tilhørende løsninger for at afhjælpe problemerne.
•
Elektromotoren
•
NL
overophedes.
F
•
E
•
Maskinen virker ikke,
•
selv om den er tilkoblet.
P
•
I
•
Det er vanskeligt at føre
•
arbejdsemnet i en ret
S
linie langs savklingen og
savskæret er
uregelmæssigt.
FIN
•
Rundsaven støjer
•
og/eller går meget
N
uregelmæssigt.
DK
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres på
en genbrugsplads.
Garanti
Garantibetingelser er beskrevet på det separat vedlagte garantibevis.
114
Motoren overbelastes,
•
Sav i et lavere tempo og
fordi der saves for store
lad motoren køle af.
arbejdsemner.
Motoren er defekt.
•
Få rundsaven repareret
eller set efter hos en
forhandler.
Fejl i netledningen.
•
Kontrollér netledningen
for brud.
Afbryderen er defekt.
•
Få rundsaven repareret
eller set efter hos en
forhandler.
Savklingen er bøjet eller
•
Udskift savklingen.
sløv.
Kulbørsterne er slidte.
•
Udskiftning af
kulbørsterne (Fig. E)
Supports must be placed under the panel on both sides, near the line of cut and near the
edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding and kickback.
f)
Blade depth and bevel adjusting locking levers must be tight and secure before making cut.
If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when making a "plunge cut" into existing walls or other blind areas. The
protruding blade may cut objects that can cause kickback.
Safety instructions lower guard
a) Check lower guard for proper closing before each use. Do not operate the saw if lower
guard does not move freely and close instantly. Never clamp or tie the lower guard into the
open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower
guard with the retracting handle and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring are not operating
properly, they must be serviced before use. Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of debris.
c)
Lower guard should be retracted manually only for special cuts such as "plunge cuts" and
"compound cuts." Raise lower guard by retracting handle and as soon as blade enters the
material, the lower guard must be released. For all other sawing, the lower guard should
operate automatically.
d) Always observe that the lower guard is covering the blade before placing saw down on
bench or floor. An unprotected, coasting blade will cause the saw to walk backwards,
cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch
is released.
Special safety instructions
Before using the circular saw:
•
Check the following points:
•
Does the voltage of the motor correspond with the mains voltage (appliances for a mains
voltage of 230V.
•
Are the mains lead and the mains plug in a good condition: solid, without any loose
ends or damage.
•
Is the saw blade missing any teeth or showing
any cracks, it so must be replaced immediately.
•
Make sure the blade is secure.
•
Use this circular saw to saw only wood, wood-like products.
•
Do not use circular saw blades wich are deformed or damaged.
•
Do not use HSS blades.
•
Only use blades meeting the required dimensions, as well as data and descriptions;
Never apply any blades of which the thickness is
greater than that of the riving knife.
•
Do not stop the blade of a circular saw by pressing the blade from the side.
•
Check that the blade guard can freely move and fully closes.
•
Never lock-up the guard in the open position.
•
Never put sideward pressure on the blade. This may cause the blade to break.
Ferm
Ferm
GB
D
NL
F
E
P
I
S
FIN
N
DK
07
Publicidad
