Specific Safety Rules - Makita HM0810 Manual De Instrucciones

ENGLISH
1 Bull point
2 Tool retainer
3 Cap
4 Red dot (Tool holder)
5 Red dot (Tool retainer)
6 Tool retainer
SPECIFICATIONS
Model
Blows per minute ..................................................................................................................... 2,900
Overall length .......................................................................................................................... 410 mm
Net weight................................................................................................................................ 5.3 kg
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal injury.
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
4. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
5. Be sure the bit is secured in place before opera-
tion.
6. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
7. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Explanation of general view
7 Press in
8 Turn 180°
9 Side grip
10 Lock button
11 Switch trigger
12 Hex wrench
8.
9.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
14. Do not operate the tool at no-load unnecessarily.
15. Some material contains chemicals which may be
GEB004-2
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing bull point or other bits
(cold chisel, etc.)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
For HM0810 (Fig. 1)
Pivot the tool retainer to the side. (If it is difficult to move
the tool retainer with your thumbs, tap it with a hammer.)
Insert the bit into the tool barrel as far as it will go. Return
the tool retainer to its original position to secure the bit.
To remove the bit, follow the installation procedure in
reverse.
For HM0810B (Fig. 2 & 3)
Press in the tool retainer and turn it until the red dots on
the tool retainer and the tool holder are aligned. Release
the tool retainer. (Fig. 2)
Insert the bit into the tool holder as far as it will go. Press
in the tool retainer and turn it a full 180 degrees. Then
release it to secure the bit. (Fig. 3)
13 Rear cover
14 Screwdriver
15 Brush holder cap
16 Lock nut wrench
17 Crank cap
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
HM0810 HM0810B
2,900
433 mm
5.3 kg
3