Special Safety Instructions - Metabo SXE 425 TurboTec Instrucciones De Manejo

power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories with
care. Check for misalignment or binding of
moving parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow safe
handling and control of the tool in unexpected
situations.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

3. Special Safety Instructions

Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Secure the workpiece against slipping, e.g. with the
help of clamping devices.
Wear ear protectors when working for long
periods of time. High noise levels over a
prolonged period of time may affect your hearing.
Hold the machine from the handles provided.
Additional Warnings:
Some dust created by power
WARNING
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
California Prop 65 08_2018
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SYMBOLS ON THE TOOL:
....... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
~
.......... alternating current
n ......... no load speed
0
../min ... revolutions per minute
rpm ..... revolutions per minute
opm ..... oscillations per minute
4. Overview
See page 2.
1 Sanding disc
2 Support plate
3 Additional handle (removable)
4 Setting wheel for selecting oscillating frequency
5 TurboBoost switch
6 Locking button for continuous activation
7 Trigger switch
8 Locking button for
"Duo" oscillating circuit setting *
9 Handle
10 Hexagon spanner
11 Ejection nozzle
12 Dust bag
13 Closure band
14 Locking screw for support plate
15 Braking ring of support plate brake
5. Commissioning
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
Always install an RCD / GFCI with a maximum
trip current of 30 mA upstream.
5.1 Additional handle (removable)
If necessary, you can unscrew the additional handle
(3) (right-hand thread).
5.2 Installation of sanding disc
Simple attachment and removal thanks to the
velcro-type fastening.
Simply press on the sanding disc such that the
ENGLISH en
5