Publicidad
Idiomas disponibles
Idiomas disponibles
position on the 3 feet when unit upside-down. Make sure
the bonnet is fitted securely and evenly around the underside
of the pad.
Before operation
Before you begin, make sure your car is clean and dry.
The work area should be dry also. If necessary, remove
road tar with a general cheaner before polishing. Also,
remove excess grease spots, bug stains etc. Using liquid
wax & paste wax Black & Decker recommends the use of
liquid wax with this polisher.
Using liquid wax (Fig. C)
Apply three swirls of liquid wax on the towel applicator
bonnet (5). Do not apply wax directly to car. This first
application should do about 1/4 of the car. For the second
and third applications of wax, use half the quantity stated
above. The bonnet will not absorb as much when reloading.
Using paste wax (Fig. D)
Spread about a heaping teaspoonful of wax evenly over the
entire surface of the towel applicator bonnet (5). Use a putty
knife or any flat object. Do not apply wax directly to car.
OPERATION (Figs. E and H)
► Fit the towel applicator bonnet (5) onto the pad (1).
► Make sure the polisher is in the off ("0") position
before plugging the polisher into an appropriate
power outlet.
► Apply wax onto the towel applicator bonnet (5) as
described on "Using liquid wax" and "Using paste
wax" section above.
► To switch your polisher on, press the on/off switch (3)
on the side marked "I". To switch it off,press the on/off
switch on the side marked "0".
Always start and stop the polisher on or against the
surface. Place the cord over your shoulder and do flat
surfaces first-hood,trunk and roof. Cover areas quickly with
broad,sweeping strokes in a criss-cross pattern (Fig.E)
► Do not press down on the polisher. The machine's
action,not pressure,does the best job.
► After flat surfaces are covered with wax,do sides of
the car. Hold the polisher as in Fig. F. Let the cord hang
free. It is not necessary to use a criss-cross motion on
doors and fenders.
► Remove the towel applicator bonnet (5) and use it to
hand-polish all hard-to-reach surfaces; under the
bumpers,around the door handles,etc. as shown
in Fig. G.
► Take off the towel applicator bonnet (5) and put a clean
polishing bonnet (6) on the polisher as described in
the section "Fitting the towel applicator or polishing
bonnet (Fig. B)" above.
► Polish the wax in the same order it was applied. Use
long,sweeping strokes in a criss-cross pattem. Do not
press hard.Let the polisher do the work (Fig. H)
HANDy HITS
► This waxer/polisher is a random orbit polisher. It is
designed to wobble. The wobbling motion produces the
fine, swirl free finish.
► For best results, use light pressure only, letting the
polisher do the work.
► The bonnets (5 and 6) can be hand-washed in
lukewarm and mind detergent, then machine dry
at the lowest setting. However,air-drying is recommended.
► Do not use abrasive compounds. Liquid wax is
recommended to use with this polisher.
► The most common error is applying too much wax.
If pad becomes saturated, it will not last as long, and
polishing will be more diffcult and take longer.
Too much wax may have been applied if:
- towel applicator bonnet (5) continually comes off pad;
- buffing seems difficult.
The polishing bonnet is only to be used for the final buff.
Do not use it to apply or remove wax.
MAINTENANCE
Your Black & Decker power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on the
tool, unplug the tool.
► Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
► Regularly clean the motor housing using a damp cloth.
► Do not use any abrasive or solvent-based cleaner.
► Regularly open the chuck and tap it to remove any dust
from the interior.
This tool is not user-serviceable. Take it to an authorized
Black & Decker repair agent for service.Your charger does
not require any maintenance apart from regular cleaning.
ACCESSORIES
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool. Black
& Decker offers a large selection of accessories available
at our local dealer or authorized service center at extra cost.
Caution! The use of any other accessory not
recommended for use with this tool could be hazardous.
ENGLISH • 13
Publicidad
