Tool Change - stayer TV509 Manual De Instrucciones

power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Check the cutting disc 6 before using. The cutting disc
must be properly mounted and must rotate freely.
Carry out a 30 second (min.) test run with no load. Do
not use damaged, out-of-centre or vibrating cutting
discs. Damaged cutting discs 6 can burst and cause
injuries.
Dusts from materials such lead-containing coatings,
minerals and metal can be harmful to one's health. Contact
with or inhaling the dusts can trigger allergic reactions to the
operator or bystanders and/or lead to respiratory infections.
Certain metal dusts are considered hazardous, especially
in conjunction with alloys such as zinc, aluminium or
chromium. Materials containing asbestos may only be
worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
The blade 6 can be blocked by dust, chips or workpiece
fragments in the slot of the bed 12.
– Switch the machine off and pull the mains plug from the
socket outlet.
– Wait until the cutting disc 6 has come to a complete stop.
– Tilt the machine toward the rear, so that small workpiece
fragments can fall out of the opening intended for this
purpose.
If required, use a suitable tool to remove all workpiece
fragments.
Prevent dust accumulation at the workplace.
Dusts can easily ignite.
Position of the Operator (see figure F)
Do not stand in a line with the cutting disc 6 in front of
the machine. Always stand aside of the cutting disc .
This measure provides for better protection of your body
against possible splinters in case of cutting disc breakage.
Switching On and Off (see figure G)
To start the machine, firstly press the lockoff button 1. Then
press the On/Off switch 2 and keep it pressed.
For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire
operation.
To switch off the machine, release the On/Off switch 2.
Soft starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
ENGLISH
22

4.2 Tool change

Before any work on the machine itself, pull the mains
plug.
Actuate the spindle lock 5 only when the tool spindle 21
is stopped. Otherwise, the machine can become
damaged.
Do not touch the cutting disc 6 after working before it
has cooled. The cutting disc 6 becomes very hot while
working.
Use only cutting discs 6 that have an equal or higher
maximal allowable speed than the noload speed of your
power tool.
Use only cutting discs 6 that correspond to the
characteristic data given in these operating instructions and
are checked according to EN 12413 and marked
appropriately.
Place unused cutting discs 6 in an enclosed container or in
the original packaging. Store cutting discs 6 lying flat.
Removing the Cutting Disc (Fig.
– Bring the power tool into the working position.
– Loosen the thumbscrew, to move the cap.
– Swing back the retracting blade guard 4 to the stop.
– Turn hexagon bolt 24 with the provided ring spanner 14
and at the same time press the spindle lock 5 until it
engages.
Advice. Alternatively lock the spindle 5, with a piece of
wood at the angle stop 7 and lock the disc 6, to proceed to
remove the disc.
– Hold the spindle lock pressed 5
hexagon bolt 24.
– Remove the washer 23 and the clamping flange 22.
– Remove the cutting disc 6.
Installing the Cutting Disc
If required, clean all parts to be mounted prior to assembly.
– Mount the cutting disc on the spindle 6 new tool holder 21
making sure that the direction of the disk according to
arrow 26.
– Mount the clamping flange 22, the washer 23 and the
hexagon bolt 24.
Press spindle lock 5 until it engages and tighten hexagon
bolt 24 with the provided ring spanner.
– Slowly guide the retracting blade guard 4 down until the
cutting disc 6 is covered off.
– Make sure that the retracting blade guard 4 operates
properly.
– Place the protective cap Flangia 28 and tighten the
thumbscrew 27.
After mounting the cutting disc 6 and before switching on,
check whether the cutting disc is properly mounted and if it
can rotate freely. Get oriented by the arrow 26.
– Make sure that the cutting disc 6 does not graze against
the retracting blade guard 4, the blade guard 19 or against
other parts.
22
B1 - B2)
and unscrew the