KENT SelectScrub 20 Instrucciones De Uso página 6

ENGLISH
INTRODUCTION
This manual will help you get the most from your Kent SelectScrub 20/26. Read
it thoroughly before operating the machine.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Kent Service
Center, who employs factory trained service personnel, and maintains an
inventory of Kent original replacement parts and accessories.
Call the KENT DEALER named below for repair parts or service. Please specify
the Model and Serial Number when discussing your machine.
(Dealer, affix service sticker here.)
NAME PLATE
The Model Number and Serial Number of your machine are shown on the
Nameplate on the machine. This information is needed when ordering repair
parts for the machine. Use the space below to note the Model Number and Serial
Number of your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRATE THE MACHINE
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it
can be inspected. Contact the Kent Customer Service Department immediately
to file a freight damage claim.
PREPARATION
WARNING!
Before any servicing, avoid possible injury or electric shock by
having machine turned off and the battery charger disconnected.
BATTERY INSTALLATION
Once the machine is completely unpacked and inspected, install the batteries
and wiring as illustrated on the diagram located inside the battery compartment.
INSTALLING THE BRUSHES OR PAD HOLDERS
1 Make sure the Brush Deck is in the RAISED position, then turn the
Master Key Switch (4) OFF.
WARNING!
Moving parts - turn the Master Key Switch (4) OFF and remove the
key before servicing.
2 If using pads, install the pads on the pad holders.
3 Align the slots on the brush or pad holder with the lugs on the drive hub.
4 Turn the brush or pad holder until it locks in place.
(1) SOLUTION FLOW DIAL
Turn this dial to the left to increase solution flow to the floor. Turn to the right, to
decrease the amount of solution flow to the floor.
On machines with traction drive, when the Drive Squeeze Bar is released from
either forward or reverse travel, the solution flow will stop automatically, and
resume when the drive is engaged.
On machines without traction drive the flow must be turned off manually by
turning the dial to the right.
6 - FORM NO. 56041439 / SelectScrub 20B/20BT/26BT
(2) BRUSH REMOVE SWITCH
To remove the brush(es) from the machine, have the machine stationary and the
brush head in the "UP" position. Press the switch to the "REMOVE" position and
release.
The switch will snap to the center off position, and the brushes will drop to the
floor. Return the switch to "SCRUB" otherwise the brush(es) will keep falling off
when the brush head is raised.
(3) BATTERY CHARGE INDICATOR
When batteries are fully charged, the needle should be in the green or yellow
zone. When in use, the needle nears the "E", batteries should be recharged.
(4) KEYLOCK SWITCH
The Keylock Switch is the master power switch.
(5) SPEED CONTROL KNOB
On machines equipped with traction drive, the Speed Control Knob is used to
adjust the traveling speed in both forward or reverse.
OTHER CONTROLS
DRIVE SQUEEZE BAR (FIGURE 1)
* Traction Drive equipped machines
Located on top at the rear of the machine, the operator can make the
machine go forward by pushing forward on it, or reverse by pulling
backward on it. When the brush head is in the "DOWN" position, the
brushes and solution will operate when the drive is engaged in either
direction, but will stop after the machine is stationary for 3 seconds.
* Brush Assist equipped machines
Located on top at the rear of the machine, the operator can start the
Brush Drive Motor by pushing forward on it when the brush head is in
the "DOWN" position. The motor(s) will stop when the bar is released.
This "dead-man" switch will not operate the Brush Drive Motor when
pulled backwards.
revised 9-02