Publicidad
WARNING: equipment under pressure built with 304 stainless steel tank;adding an unsuitable substance inside the
tank could be cause of a serious EXPLOSION HAZARD !!!
The Sprayer has been designed and built so that it can contain fluids classed in Group 2 defined as non dangerous
(see Directive 67/548/EEC Art.2, Section 2 and Directive 97/23/EEC Art. 9) inside its tank and atomize them. Hence
it is STRICTLY PROHIBITED to add any fluid classed in Group 1 into the tank and in particular all the fluid defined
as: explosive, extremely flammable, highly flammable, flammable, very toxic, toxic and oxidizing
Furthermore, it is STRICTLY PROHIBITED introduce inside the tank substance which could be corrosive for 304
stainless steel (chlorine, etc.) and which could attack the tank walls with consequent serious risk of explosion. In this
connection, BEFORE adding the liquid in the tank, IT IS COMPULSORY for the user to consult relative product data
and safety sheet or the supplier of the substance to be sprayed.
The Sprayer is a pressure equipment provided with trolley to make it portable. IT IS PROHIBITED to pull or push the
Sprayer using mechanical means in any way whatsoever.
It is FORBIDDEN to use the Sprayer to atomize towards: persons, animals, machines or objects provided with
electrical motors or electrical equipment which, upon contact with the liquids, could cause short circuits.
THE USERS MUST COMPLY WITH THE LAWS ON THE OPERATIONS OF PRESSURE EQUIPMENT IN
3 - NOZZLE CONNECTION
before using the sprayer, the lance and pipe provide must be connected. To do so, it is necessary to:
3.1 insert one end of the pipe into the bayonet joint on the lance
3.2 insert the other end of the pipe into the bayonet joint on the „liquid outlet" (2.5)
4 - INSERTION OF PRODUCT
Fill the tank with the product to be sprayed through the „loading cap" (2.1). Before opening the cap, it is necessary to:
4.1 check by means of the pressure gauge (2.3) that the tank is NOT under pressure; should that not be the case, open the „air entry"
tap (2.4) and let all the air out
of the tank
4.2 unscrew the „loading cap" (2.1) and insert the product to be sprayed using a suitable funnel
4.3 close the „loading cap" (2.1) by screwing tightly. The sprayer is now ready to be pressurized
5 - PRESSURIZATION OF THE TANK
5.1 connect the sprayer by means of the „air entry" tap (2.4) to your air compressor
5.2 open the „air entry" tap (2.4) and pressurize the sprayer to desired pressure ATTENTION: MAXIMUM WORKING PRESSURE 8
BAR
6 - DISTRIBUTION OF PRODUCT
the characteristic of the sprayer/foamer is that it can be used either as a sprayer or as a foam generator
USE AS SPRAYER
6.1 open the "liquid outlet" tap (2.5) to which the pipe with nozzle has been previously connected (3), making sure the "mixing" tap (2.6)
is closed
6.2 assemble the head with fine cut and hole (N) on to nozzle terminal
6.3 grasp the nozzle and pull the handle making sure to point the jet of liquid only in the direction of the surface to be treated
USE AS FOAMER
6.4 open simultaneously the "liquid outlet" tap (2.5) and the "mixing" tap (2.6)
6.5 assemble the head with larger cut and hole on to nozzle terminal, in particular:
- the "S1" head for less dense foam
- the "S2" head for denser foam
6.6 grasp the nozzle and pull the handle making sure to point the jet of liquid only in the direction of the surface to be treated
ATTENTION: it is possible to regulate the density of the foam by using the "mixing" tap (2.6), opening or closing it slightly according
to whether a greater or
lesser density is required
6.7 when there is still some product left in the tank but insufficient pressure to distribute it, repeat operations from point 5
6.8 when the product in the tank is finished but the further distribution is necessary, repeat operations from point 4
ATTENTION: NEVER LEAVE ANY UNUSED PRODUCT TO DEPOSIT IN THE TANK; AFTER USE, EMPTY COMPLETELY
AND RINSE
THOROUGHLY
Seite 6 von 9
FORCE IN THE RELATIVE COUNTRY
MODE OF USE
.
Publicidad
