Initial Start-Up - Milwaukee 2258-20 Manual Del Operador

SYMBOLOGY
Read operator's manual
CAUTION
WARNING
Radiation Is Emitted From This Aperture
European Conformity Mark
SPECIFICATIONS
Cat. No. ..................................................... 2258-20
Volts .............................................................. 12 DC
Battery Type .................................................M12™
Charger Type ................................................M12™
Temperature Measurement
Infrared (IR) Resolution ...................102 x 77 pixels
(Picture Elements or Data Points)
Object Temperature Range 2 ............14°F to 626°F
Thermal Sensitivity ..................... 0.1°C/25°C NETD
(Noise Equivalent Temperature Difference)
Spatial Resolution............................ 3.0 mrad IFOV
Accuracy ................................ ±5°C or 5% @ 25°C,
On-board Adjustable Emissivity ......... Variable from
0.10 to 1.00, in increments of 0.01
Infrared (IR) Detector Type .......................Uncooled
microbolometer focal-plane array (FPA)
Spectral Range ................................... 7.5 to 14 μm
Thermal Imaging
Field of View (FOV) ......26.8° (Horiz.) X 35.4°(Vert)
Focus Method ...................................... Fixed Focus
Minimum Distance in Focus .............36" (91.4 mm)
Screen Refresh................................................ 8 Hz
Physical and Environmental
Drop Test .........................6' (2 m) Drop to concrete
Operating Temperature Range ..........14°F to 122°F
Operating Storage Humidity Range......... 10%-90%
Laser
Maximum Power ........................................... <1mW
Wave Length ........................................ 630-670nm
Class......................................................................II
Laser Complies with ..... 21CFR 1040.10 & 1040.11
General
Image Storage Included .... Removable 8GB SDHC
Tested to accept an SDHC card up to 32GB.
Data Communication Interface .............. Micro USB
Display ..........................Color TFT-LCD 2.4" (6 cm)
NOTE: Displayed readings < -10°C and > 330°C
are not specified. The LED floodlight does not affect
thermal images.
Laser Light -
Do Not Stare Into Beam
Laser product
Avoid Exposure: Laser
(-10°C to 330°C)
(Instantaneous Field of View)
whichever is greater
(-10°C to 50°C)
Non-condensing
measured diagonally

INITIAL START-UP

The first time the Infrared Camera is turned on, you
are required to select the Language, Time, and Date.
See Personal Settings for more information.
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
A fuel gauge on the Infrared Camera
display shows the remaining battery
charge. At approximately 10% re-
maining charge, the fuel gauge will
begin to blink red. When no charge
remains, a Low-Battery Message
appears on the display for 3 sec-
onds before the Infrared Camera
shuts down.
Power-Saving Features
To preserve battery life, the Infrared Camera goes
into Sleep Mode after 5 minutes of no activity. Sleep
Mode maintains a ready-to-go, warmed-up condition,
but uses little battery power. To reactivate the tool,
pull the trigger or press any button. After another
15 minutes of no activity, the Infrared Camera turns
itself completely off. Press the power button to turn
the tool back on.
Removing/Installing the SDHC Memory Card
Install the SDHC card before use. The Infrared Cam-
era does not store any images without one installed.
To install or remove:
1. Turn off the tool.
2. Open the rubber media door.
3. To remove, press in and release. The SDHC card
will pop out. Pull out the card.
4. To install, slide the SDHC card into the slot and
press in firmly. The label on the SDHC card should
face the display of the Infrared Camera.
5. Close the media door.
NOTE: A display notification will alert you
when the SDHC card is missing, almost full,
and again when it is full. Delete or transfer
images to another device to free up space on
the SDHC card, or use another SDHC card.
3
SET-UP
Battery life
100%
75%
50%
25%
<10%