Milwaukee 2258-20 Manual Del Operador página 5

Taking a Thermal Image
An SDHC card must be installed for the Infra-
red Camera to save images and data. If no
SDHC card is installed, the error message
"NO SD CARD" is displayed.
1. Use the steps under "Taking a Temperature Mea-
surement" section to frame the desired image on
the display.
2. The Target Temperature, color palette, and any
displayed marks will be captured in the image.
3. Pull the trigger fully to take the picture.
4. To save the image, press the OK button or pull
the trigger again.
5. To cancel the image, use the arrow ◄► buttons to
select Cancel, then press the OK button.
Image Review
To review the saved images on the display:
1. Press the Image Review
button.
2. Use the arrow ◄►buttons to
scroll through the images.
3. To delete an image, press
the OK button to select the
displayed image, then use the
arrow ◄► buttons to select
Delete. Press the OK button
again.
4. Use the DELETE ALL function
in Settings to batch-delete
the images.
5. To return to live view, press the Image Review
button again.
Selecting the Emissivity
Emissivity is an internal setting that is used to adjust
the tool based on the type of material being mea-
sured. Different materials emit radiation differently
and changing the emissivity value will provide a
more accurate temperature based on the material
being measured. Select the material or emissivity
level in Settings .
1. Press the Settings
2. Use the arrow ▲▼ buttons to select EMISSIVITY.
3. Press OK.
4. Emissivity can be set by ratio or material.
Use the arrow ◄► buttons to select the ratio col-
umn or the material column. Then, use the arrow
▲▼ buttons to select the desired ratio or material.
5. Press OK.
Target Materials and Corresponding
Emissivity Ratios
Emissivity
Material Ratio
Aluminum * 0.30
Asphalt 0.95
Brick 0.83
Concrete * 0.95
Copper 0.60
Iron 0.70
Oil
0.94
(Petroleum)
*Available Material Setting in the EMISSIVITY menu.
button.
Emissivity
Material Ratio
Paint 0.93
Rubber 0.95
Sand 0.90
Soil 0.92
Steel * 0.80
Water * 0.93
Wood 0.94
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Obtaining Technical Support or Service
Your tool should not need calibration, however, to
obtain documentation that your tool meets specifica-
tions, contact the nearest service center. The tool will
be sent out for testing, and you will receive it back
with proper documentation.
Maintaining Tool
Keep your tool, battery pack and charger in good re-
pair by adopting a regular maintenance program. Af-
ter six months to one year, depending on use, return
the tool, battery pack and charger to a MILWAUKEE
service facility for:
• Lubrication
• Mechanical inspection and cleaning (gears, spin-
dles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger, motor)
• Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
Cleaning the Lens
Blow off loose particles with clean compressed
air. Carefully wipe the surface with a cotton swab
moistened with water. Using a second cotton swab,
dry completely.
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
5
Cleaning
Repairs