General Operation; Listening To Radio - AEG MC 4461 BT Instrucciones De Servicio

English
46
Setting the time
The time can only be set when the device is in standby.
1. Press the CLK SET button (9/6) for about 2 seconds. The
display for the year (YEAR) will start to blink.
2. Perform the setting with the
3. Press the CLK SET button to save the entry.
4. Repeat steps 2 – 3 to consecutively perform the settings
for month (MONTH), day (DATE), time format (24 or
12 hour display), hours or minutes.
NOTE:
• The following will appear in the display with the 12-hour
display:
AM = Morning, PM = Afternoon.
• The setting for the weekday is done automatically.
• The stored time is lost as soon as the power supply has
been interrupted.

General Operation

NOTE:
Some buttons are located both on the device and on the
remote control. Identical buttons have the same effect.
Turning On / Off the Device
• Turning on: Press the / FUNCTION button (11/9) to turn
the device on
• Turning off: Press the / FUNCTION button (11) on the
device for about 2 seconds or press the
the remote control. The time will show on the display.
NOTE: Automatic standby function
The USB port from your device is also suitable for charging
your smartphone. The music center must be turned on for
this purpose. In order to comply with the "ErP 2 (Energy-re-
lated Products)" Eco-design Directive (2009 / 125 / EC) that
is aimed at improving energy efficiency and general envi-
ronmental compatibility of electrical appliances, the de-
vices must switch off independently after a certain amount
of time without a signal. After approx. 20 minutes without
signal or with very poor signal, the device will automatically
switch to standby.
Volume
You can use the / (5/6) buttons on the device, or
V−/AL1 / V+/AL2 (7) on the remote control to set the desired
volume.
Preset Equalizer Function
Different sound modes are available (F = FLAT, C = CLASSIC,
r = ROCK, P = POP, J = JAZZ). To select the sound modes,
proceed as follows:
1. Press the button (7) for about 3 seconds. The currently
set sound mode will be displayed.
MC4461BT_IM_new2 ab PO7108
2. Press the
3. If no other button is pressed within about 2 seconds, the
/ buttons.
Headphone Jack (Back of the Device)
For headphone operation, use headphones with a 3.5 mm
jack plug which you insert into the PHONES headphone jack.
The speakers are turned off.

Listening to Radio

1. Completely unwind the dipole antenna.
2. Repeatedly press the / FUNCTION button (11) on the
3. Use the control (8) to set the desired station. The respec-
Play Back Music via Bluetooth
Bluetooth involves a technology for wireless radio connection
of devices over a short distance. Devices with Bluetooth
standard are transmitting between 2.402 and 2.480 GHz in
button (9) on
the ISM band (Industrial, Scientific and Medical). Interference
can be caused for example by WLAN-networks, DAB radios,
cordless phones, or microwave ovens which work on the
same frequency band.
This device offers you the possibility to use a Bluetooth-en-
abled device. The functional radius is limited to approx.
15 metres depending on the surroundings and the device
used.
If your playing device supports the A2DP profile (Advanced
Audio Distribution Profile) and has a music-player function,
then you can also wirelessly transfer music to the device.
The A2DP profile involves a multi-vendor Bluetooth profile.
By streaming, stereo-audio signals are wirelessly transferred
between the playing device (source) and the receiving
device. To be able to remotely control the source, the play-
back device must support the AVRCP profile (Audio Video
Remote Control Profile.
Due to the different device manufacturers, models, and
software versions, a full functionality cannot be guaranteed.
button again while the sound mode is being
displayed.
setting will be accepted. The set sound mode cannot be
permanently shown in the display for technical reasons.
device, or FUNC (1) on the remote control until "FM" is
displayed.
tive frequency is shown on the display.
NOTE:
If the received station has atmospheric noise, try to improve
the reception by changing the position and unwinding or
winding up the antenna.
29.12.16