Dolmar EM411 Manual De Instrucciones página 16

Mowing a long-grass lawn
Do not try to cut long grass all at once. Instead, mow
the lawn in steps. Leave a day or two between mowings
until the lawn becomes evenly short.
► Fig.35
NOTE: Mowing long grass to a short length all at
once may cause the grass to die. The cut grass may
also block up inside of the mower body.
Edge mowing
When mowing at the edge, be sure to face the left side
of the machine toward the edge, and then move the
machine along the edge.
► Fig.36
MAINTENANCE
WARNING:
Before performing the mainte-
nance, unplug the extension cord from the power
supply, and confirm that the blades have come to
a complete halt.
CAUTION:
When performing the mainte-
nance, always wear gloves.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita/Dolmar Authorized or Factory
Service Centers, always using Makita/Dolmar replace-
ment parts.
Maintenance after mowing
After mowing, wipe the machine with a dry cloth or a
cloth dipped in soapy water. Also, use a soft brush to
brush off grass cuttings and dirt from blades.
Never use gasoline, benzine, thinner,
NOTICE:
alcohol or the like. Discoloration, deformation or
cracks may result.
Storing
1. Disconnect the extension cord.
► Fig.37: 1. Extension cord
Remove the grass basket.
2.
Set the mowing height with the adjusting lever.
3.
For EM411:
Set the mowing height to "2".
► Fig.38: 1. Adjusting lever
For EM462/EM463S:
Set the mowing height to "4".
► Fig.39: 1. Adjusting lever
Open the levers of the handle outside while hold-
4.
ing the upper handle, then set the handle height to the
middle, and then close the levers.
► Fig.40: 1. Lever 2. Mark 3. Arrow
Before opening the levers, hold
CAUTION:
the upper handle firmly. Otherwise, the handle
may fall and cause an injury.
5. Loosen the thumb nuts while holding the handle.
► Fig.41: 1. Thumb nut
6. Widen the handle outside a little, and then fold the
handle and insert the protrusions on the handle into the
holes.
► Fig.42: 1. Handle 2. Protrusion 3. Hole
When folding the handle, be care-
CAUTION:
ful not to pinch your hand or fingers.
Tighten the thumb nuts.
7.
► Fig.43: 1. Thumb nut
Place the machine as shown in the figure.
8.
► Fig.44
CAUTION:
Be sure to store this machine
indoors and place it on a flat surface. Otherwise,
the machine may fall and cause an injury.
Replacing the mower blade
CAUTION:
Do not use any wrench other than
the standard hex wrench when replacing the
mower blade. Using a different wrench may lead to
over-tightening or looseness, which may cause injury.
1. Unplug the extension cord and stand up the
machine. (Refer to the instructions for storing.)
2. Insert the pin into the hole, and then hold the han-
dle with one hand and loosen the bolt with the wrench
counterclockwise.
► Fig.45: 1. Blade 2. Wrench 3. Pin
Remove the mower blade.
3.
For EM411
Remove the bolt, washer, mower blade, bracket, and
spacer in order.
► Fig.46: 1. Spacer 2. Bracket 3. Mower blade
4. Washer 5. Bolt
For EM462/EM463S
Remove the bolt, mower blade, and bracket in order.
► Fig.47: 1. Bracket 2. Mower blade 3. Bolt
4. Attach a new mower blade, then insert the pin into
the hole, and then hold the handle with one hand and
tighten the bolt with the wrench clockwise firmly.
► Fig.48: 1. Mower blade 2. Wrench 3. Pin
Adjustment of cable
For EM463S
If the rear wheels do not rotate or do not rotate smoothly
when you squeeze the drive lever, adjust the length of
the cable.
1. Loosen the nut with a wrench while holding the
sleeve with another wrench.
► Fig.49: 1. Sleeve 2. Nut
16 ENGLISH