Specific Safety Rules - Makita HP2040 Manual De Instrucciones

ENGLISH
1 Teeth
2 Protrusions
3 Loosen
4 Tighten
5 Side grip
6 Chuck key
SPECIFICATIONS
Model
Max. capacities
Concrete ..........................................High: 20 mm
Steel ................................................High: 8 mm
Wood ...............................................High: 25 mm
-1
No load speed (min ) .........................High: 0 – 2,900
Blows per minute ................................High: 0 – 37,700
Overall length ................................................. 364 mm
Net weight....................................................... 2.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer drill safety rules. If you use this power
tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Wear ear protectors with impact drills. Exposure
to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
4. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
5. Hold the tool firmly with both hands.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
Explanation of general view
7 Sleeve
8 Ring
9 Depth gauge
10 Switch trigger
11 Lock button
12 Reversing switch lever
HP2040
Low: —
Low: 13 mm
Low: 40 mm
Low: 0 – 950
Low: 0 – 12,400
8.
9.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Important:
Always be sure that the tool is switched off and
GEB003-2
unplugged before installing or removing the side grip, bit
or other accessories.
Side grip (auxiliary handle) (Fig. 1)
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
Installing or removing drill bit
For HP2040 and HP2042 (Fig. 2)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the origi-
nal position.
13 Speed change knob
14 Action mode change button
15 Blow-out bulb
16 Vent holes
HP2041
20 mm
—
8 mm
13 mm
25 mm
40 mm
0 – 2,900
0 – 950
0 – 37,700
0 – 12,400
364 mm
2.3 kg
Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
HP2042
20 mm
—
8 mm
13 mm
25 mm
40 mm
2,900
950
37,700
12,400
364 mm
2.3 kg
5