babymoov Babyphone Expert Care Instrucciones De Uso página 11

A / Baby unit
• Long press the power ON/OFF button (1) for 3 sec to switch on the unit. The power on icon (7)
should light up steady green. To turn off, long press the button (1) again.
• Place the unit about 1 m from the crib with the microphone (11) facing towards the baby.
• Adjust the microphone sensitivity using the button (2) and button (3) such that the unit will be set to
transmit whenever the microphone (11) picks up a sound at your desirable loudness level. The intensity
of night light (6) will change during adjustment. The higher the intensity, the more sensitive is the
microphone 11 to sound. There are total 5 levels of microphone sensitivity. When the maximum level
is reached, further press of the button (3) will set the unit into continuous transmission mode (i.e. the
unit will transmit even without detecting a sound) and the icon (10) will light up steady green.
• Once the unit is in transmit mode, the transmit icon (8) will light up green. The unit will return to
standby mode a few seconds after the microphone (11) stops picking up any sound and the transmit
icon (8) will go off. Except when the unit is set in continuous transmission mode, the transmit icon (8)
will stay steady on.
• The night light (6) can be set permanently ON by pressing the button (4). Each press of button (4) will
increase the level of light intensity (maximum 5 levels). The night light (6) can also be set to VOX
(voice activated) by pressing button
• Under VOX mode, the icon (9) will light up and night light (6) will be switched on once the microphone
(11) detects a sound and automatically fade off a few seconds after the sound stops.
• The condition of the battery is shown by the power on/low battery icon (7). When the battery level
becomes running low, the power on/low battery icon (7) turns red. Replace with new battery or use
the supplied AC adapter.
Parent unit
• Long press the power ON/OFF button 13 for 3 sec to switch on the unit. The power on icon 18 should
light up steady green. To turn off, long press the button 13 again.
• Place this unit at a reasonable distance away from the baby unit to avoid feedback. Too close a distance
will create a screeching sound at the speaker 21.
• Once it receives a signal from the baby unit, the visual level meter 17 will light up. The number of segments
being lighted up vary along with the sound. This feature is useful in case the parents prefer to turn down
the speaker volume to keep the environment quiet.
• The speaker volume can be adjusted using the button 14 and button 15 . Each press of button will
change the volume by 1 step which is correspondingly indicated by the visual level meter 17. There are
total 5 volume levels, more segments shown in visual level meter 17 means higher volume. When the
volume setting is at minimum, further press of button 14 will cause the speaker 21 to be totally muted
with the icon 20 being lighted up.
• This unit is equipped with a vibration alert. Press the button 16 and the icon 19 will show up. Once the
received baby's voice is loud enough, the vibrator starts to function. This feature is useful when the parent
is working under noisy environment (e.g. vacuum cleaning). To save battery power, it is recommended
not to use the vibration alert frequently. To switch off vibration, press the button 16 again and the icon 19
goes off.
• Once this unit is beyond the communication range of baby unit for over 30 sec, an out of range alarm will
be heard together with segments of the visual level meter 17 flashing to alert the parents. The alarm
sound is independent of whether the speaker is muted or not. This alarm will go off only when the parent
unit falls back within the communication range of baby unit.
N.B. This alarm will also be heard in case the baby unit is switched off, or its battery has run down, or its
power is cut off, or the pairing is not properly done between the baby and parent unit.
• The condition of the Li battery pack is shown by the power on/low battery icon 18 . When battery level
becomes running low, the icon 18 turns red and an alarm will be heard, reminding the parents to charge
up the battery using the supplied AC adapter.
• Each time the buttons are pressed, a beep tone will be heard. To eliminate this beep tone, press and
hold the button 14 for 2 sec until a second beep tone is heard. To resume the beep tone, press and hold
the button 15 for 2 sec until a beep tone is heard. Whenever the unit is switched off and then on again,
the beep tone will resume automatically.
OPERATION
BABYPHONE EXPERT CARE • Instruction manual
11