Programming The Guest Mode; Taking Weight Measurement Only; Troubleshooting; Specifications - Tanita InnerScan 50 Manual De Instrucciones

3. Recall Function
The previous readings of the following features can be obtained using the recall function.
Weight
Body Fat %
Total Body Water %
Muscle Mass and Physique Rating
BMR and Metabolic Age
Bone mass
Visceral Fat Level
To obtain previous readings, press the RECALL button while the current readings are being displayed.
To see other previous readings, press the appropriate feature button for each desired reading.
Press the RECALL button again to go back to the current readings.
Note: F or children (age 5-17), the unit will only display the Weight and the Body Fat % (it will not display the Healthy Range
Indicator).
Programming the guest mode
Guest mode allows you to programe the unit for a one-time use without resetting a
Personal data number.
Press Guest button to activate the unit. Then follow the steps:
Set Age, Select Female or Male, and Specify Height.
Note: If you step onto the platform before "0.0" appears the display will show "Error" and
you will not obtain a reading.
Taking weight measurement only
Select Weight-Only Key
Press the Weight-only key. After 2 or 3 seconds, "0.0" will appear in the display and the unit
will beep. When "0.0" appears in the display, step onto the platform. The body weight value will
appear. If you remain on the platform, the display will flash for about 30 seconds, and then the
power will automatically turn off.
If you step off the platform, the weight will continue to show for about 5 seconds, then
"0.0" will appear and the unit will shut off automatically.


Troubleshooting

If the following problems occur ...then...
• A wrong weight format appears followed by kg, lb, or st-lb.
Refer to Switching the weight mode on p.3.
• The display shows and goes off when the personal key is pressed.
No data (age gender, height and activity level) has been stored in the memory.
• appears on the display, or all the data appears and immediately disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will affect the
accuracy of your measurements. Change all the batteries at the same time with new batteries.
Note: Y our settings will not be erased from the memory when you remove the batteries.
• appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
• The Body Fat Percentage reading does not appear or
Your personal data has not been programmed. Follow the steps on p.4.
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides on the
measuring platform.
• appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded.
• No reading is obtained after pressing a feature button.
Step off scale when body fat reading appears, then press feature button.

Specifications

BC-351
Weight Capacity
150 kg (330 lb) (23 st 8 lb)
Weight Increments
0.05 kg (0.1 lb) (0.1 lb)
Body Fat Increments
0.1%
Personal Data
As consumer you are legally bound to return used or discharged batteries.
4 memories
You can deposit your old batteries at the public collecting points in your
Power Supply
town, or wherever the corresponding batteries are sold and specifically
2pcs.Lithium batteries CR2032 (included)
marked collecting boxes have been set up. In case of scrapping the
Power Consumption
apparatus, the batteries should be removed from it and deposited at the
60 mA maximum
collecting points as well.
Measuring Current
50 kHz, 6.25 kHz, 100 µA
appears after the weight is measured.
Notice:
These marks can be found out on contaminant-containing
Batteries:
Pb Pb = Battery contains lead,
Cd Cd = Battery contains cadmium,
Hg Hg = Battery contains mercury.
Not allowed to mix batteries with consumer wastes!
The device features radio interference suppression in
compliance with EC regulation 2004/108/EC