Taking Body Composition Readings; Programming The Guest Mode; Taking Weight Measurement Only; Troubleshooting - Tanita InnerScal BC-534 Manual De Instrucciones

GB

TAKING BODY COMPOSITION READINGS

1. Select Personal Key and Step On
Press your pre-programmed Personal key.
(Release the key within 3 seconds or the display will show "Error".)
The unit will beep and the display will show the programmed date.
The unit will beep again and the display will show "0.0".
Now step onto the platform.
Note: If you step onto the platform before "0.0" appears the display will show "Error" and
you will not obtain a reading. Furthermore, if you do not step onto the measuring platform
within about 30 seconds after "0.0" appears, the power is shut-off automatically.
2. Obtain Your Readings
Your weight will be shown first.
Continue to stand on the platform.
"00000" will appear on the display and disappear one by one from left to right.
Your Body Fat percentage(%FAT) and Body Fat Range will appear on the
display screen.
After your body fat percentage has been calculated, a black bar will flash
along the bottom of the display, identifying where you fall within the Body
Fat Ranges for your age and gender
Note: Do not step off until Body Fat % is shown.
To see other readings, Carefully step off scale, press other feature keys.
The feature keys will not function while remaining on scale.
To see other readings press each feature key while weight & Body Fat % is
displayed.
Press same feature key to display weight & Body Fat % again.
Note: The following readings are applicable only to adults aged
18 years to 99 years.
・Press key to display Total Body Water % .
・Press key to display Bone Mass.
4
・Press
key to display DCI & Metabolic Age.
・Press key to display Previous weight &
Body Fat %.
( Applicable age 7-99 years )

PROGRAMMING THE GUEST MODE

Guest mode allows you to programme the unit for a one-time use
without resetting a Personal data number.
▲
Press
Set Age, Select Female or Male, and Specify Height.
Note: If you step onto the platform before "0.0" appears the display will show
"Error" and you will not obtain a reading.

TAKING WEIGHT MEASUREMENT ONLY

Select Weight-Only Key
Press the Weight-only key. After 2 or 3 seconds, "0.0" will appear in the
display and the unit will beep. When "0.0" appears in the display, step onto
the platform. The body weight value will appear. If you remain on the platform,
the display will flash for about 30 seconds, and then the power will automatically turn off.
If you step off the platform, the weight will continue to show for about 5 seconds, then
"0.0" will appear and the unit will shut off automatically.

TROUBLESHOOTING

If the following problems occur ...then...
・A wrong weight format appears followed by kg, lb, or st-lb
Refer to Switching the Weight Mode on p.2.
・"Lo" appears on the display, or all the data appears and immediately
disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will
affect the accuracy of your measurements. Change all the batteries at the same time with new AA-size batteries.
Note:Your settings will not be erased from the memory when you remove the batteries.
・"Error" appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
・The Body Fat Percentage reading does not appear or "----- " appears after
the weight is measured.
Your personal data has not been programmed. Follow the steps on p.3.
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides
on the measuring platform.
・"OL" appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded
・No reading is obtained after pressing a feature key.
Step off scale when body fat reading appears, then press feature key.
button to activate the unit. Then follow the steps:
GB
5