Push Stick - Rockwell RK7241S Manual De Instrucciones

Jobsite table saw with laser
warNiNG: NEVER use the fence as a cross-cut
length stop. This is extremely dangerous, if the
work twists even a tiny amount it will jam between the
fence and blade and be flung forward very violently,
possibly dragging the operator's hand through the blade.
5. the Miter GauGe (see P)
The miter gauge (18) can be locked at the desired angle
by twisting the handle. always hold the work firmly
against the face of the miter gauge.
for additional support, 2x1 wood can be attached to
the miter gauge face using screws though the holes
provided.
6.the outFeeD suPPort (see K1)
The outfeed support extends to provide additional
support for long workpieces.
7. to use the laser Cut liNe iNDiCator (17)
(see q)
CauTiON--use of controls or adjustments or
performance of procedures other than those specified
herein may result in a hazardous radiation exposure.
CauTiON--The use of optical instruments with this
product will increase eye hazard.
To fit the batteries, remove the battery storage cover
by lifting the left end (m) of the cover upward (sEE Q).
insert 2 x aaa batteries, then replace the cover.
Note: Ensure correct battery polarity.
To use the laser guide, simply press the laser on/off
switch (n). The laser guide then projects a visible red
line on the saw table in front of the blade.
Note that the line will move as the blade is beveled, this
is correct operation. The laser line is only used to align
cutting marks on the workpiece.
Note the actual cut must still be guided by the fence or
miter gauge.
(This laser is much safer than guard mounted lasers
which can be misused for very dangerous free hand
cutting).
Note:
1) switch off the laser when you stop the machine. The
laser does not turn off automatically.
2) The laser is adjusted accurately in the factory. it is
not user adjustable. Remove the batteries if not used
for long periods (many months).(see R)

8. Push stiCK(4)

use a push stick whenever the fence is 2 inches or less
from the blade.
18
The push stick should be used in the place of the user's
hand to guide the material only between the fence and
blade.
When using a push stick, the trailing end of the board
must be square. a push stick against an uneven end
could slip off or push the work away from the fence.
9. oN/oFF saFetY switCh (see q)
To turn the machine on, lift the switch to the "ON"
position. To turn it off, press the switch down to the
"Off" position.
to "lock" the machine:
When the machine is not in use and to prevent
unauthorized use, the switch should be locked in the
"Off" position. To do this, pull the locking key (o) out of
the ON/Off switch and store the key in a secure place.
With the key removed, the switch will not operate.
10. oVerloaD ProteCtioN (see q)
The machine is equipped with a overload reset switch
(9) that will restart the motor after it shuts off due to
overloading or low voltage. if the motor stops during
operation, move the ON/Off switch to the "Off"
position.
Remove any workpiece from the table. Wait about
5minutes for the motor to cool down, and then push the
reset button and move the switch to the "ON" position.
11. tYPes oF Cuts
warNiNG: Make sure the blade guard assembly
is installed and is working properly to avoid
possible serious injury.
warNiNG: Never make freehand cuts (cuts
without the miter gauge or rip fence). This can
result in serious injury.
1) Cross cut (see s1)
Cross cut is cutting wood across the grain at 90° or
square with both the edge and the flat side of the wood.
This is done with the miter gauge set at "0°". before
using it, make sure it is locked. The miter gauge can be
used in either of the miter slots in the table.
Note: NeVer use the rip fence as a length stop,
store the rip fence off the table when cross-
cutting.
- MaKiNG a Cross Cut:
set the blade to the correct depth for the workpiece.
set the miter gauge to 0° and tighten the locking knob.
Make sure the wood is clear of the blade before turning
on the saw.
eNG