Technical Data; Residual Risks; Before Starting The Equipment - Bavaria BCS 64/1 Manual De Instrucciones

4. Technical data

Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

Residual risks

Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Anl_BCS_64_1_SPK8.indb 20 Anl_BCS_64_1_SPK8.indb 20
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
•
Release the handle on the rear of the guard
hood for adjusting the cutting depth (4).
•
Place the saw foot (6) flat on the surface of
the workpiece you wish to saw. Raise the saw
until the saw blade (12) is at the required cut-
ting depth (a).
•
Refasten the handle for adjusting the cutting
depth (4). Check the handle is securely faste-
ned.
5.2 Miter stop (Figure 4/5)
•
The preset standard angle between the saw
foot (6) and the saw blade (12) is 90°. You can
adjust this angle to carry out angled cuts.
•
Undo the two locking screws for miter setting
(7).
•
You can now adjust the cutting angle by up to
45°. Keep an eye on the cutting angle scale
(9) as you do so.
•
Refasten the locking screws for miter setting
(7). Check that everything is securely faste-
ned.
5.3 Extraction of dust and chips (Fig. 6/7)
•
Connect your circular saw to a suitable vacu-
um cleaner using the dust extractor adaptor
(20). Then insert the dust extraction adaptor
(20) into the sawdust extraction outlet (14)
provided on the hand-held circular saw. You
can then connect a suitable vacuum cleaner
(a) to the dust extractor adaptor (20) (vacu-
um cleaner not supplied). This will provide
excellent dust extraction on the workpiece.
The benefits are that you will protect both the
equipment and your own health. Your work
area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety inst-
ructions".
•
Important! The vacuum cleaner you use for
the extraction work must be suitable for the
workpiece material.
•
Check that all the parts are properly connec-
ted.
- 20 -
27.11.14 12:53 27.11.14 12:53