Olymp LavaSit DINER Shiatsu Instrucciones De Montaje página 7

Mounting instructions for electricians:
During assembly work the complete system
•
must be isolated from the power supply and
secured against unintended switch-on!
In the wash unit, use only the plug-in connectors
•
supplied with the appliance and specified in the
mounting instructions!
Cables must be so arranged that they are not in the
•
vicinity or moving parts! Damage or crushing must
thus be prevented!
The power supply cable from the unit must be
•
arranged so that it is not jammed between the
unit frame and the floor.
The mains cable must be led outward completely and
•
provided with strain relief.
For reasons of mechanical security as well as the
•
electromagnetic compatibility no cable excess may be
stowed away in the shampoo unit.
Variants for single units:
10.1 Direct connection variant: (fig. 6)
Caution: This type of connection must only be
made by a qualified electrician!
- Connect the mains cable from the floor to the
supplied system socket (fig. 4)
- Insert the socket into the system connector
underneath the cover section and fasten the
locking clip (fig. 5).
10.2 Mains cable variant: (fig. 7)
Lead the mains cable with plug to the outside in
the rear area of the backside cover (cable will be
later set through the installation tunnel to wall plug
socket).
In-line installation variants:
10.3 In-line installation with direct connection (fig. 8)
Caution: This type of connection must only be
made by a qualified electrician!
Connect the mains cable from the floor to the
supplied system socket (fig. 4)
Insert the socket into the system connector
underneath the cover section and fasten the
locking clip (fig. 5).
10.4 In-line installation with mains cable (fig. 9)
Lead the mains cable with plug of the wall side
unit to the outside in the rear area of the backside
cover ( will be later set through the installation
tunnel to wall plug socket).
Lead the mains cable with plug of the 2
outside under the seat.
Diner Shiatsu MO W+R
GB
Mounting instructions for appliance fitters:
11.
11.1
11.2
11.3
11.4
11.5
11.6
11.7
nd
unit
12.
Assembly:
Loosely bind the 2 pressure hoses (hot + cold) and drain
hose together using cable ties.
Hang the backside cover (1) onto the base:
Hold the cover at the front edge from both sides, pull
apart and draw it from the rear side onto the base:
Front edge of cover must engage in perpendicular
profile.
Unit with mains cable:
Route the mains cable of the wall side unit through the
cutout in the backside cover.
Put in the front cover (2) under the seat.
Attach the mounting strip (5) for installation tunnel
onto the backside cover over the cutout (fig. 2).
Attach the mounting strip (5.1) for installation tunnel
onto the wall (fig. 3).
Shorten the installation tunnel on the wall side if
neccessary.
Lay the installation tunnel onto the mounting strips.
Caution:
The ends of the installation tunnel must be fitted with
edge protection!
Unit with mains cable:
Fix 3 self-adhesive cable clips (6) to the inner side of
the installation tunnel fig. 3
Fix mains cable in cable clips, plug mains cable into plug
socket at the wall.
Only with in-line installation for water pipes:
Attach mounting strips (5) for installation tunnel
onto the backside cover over the cutout at both units
(fig. 2).
Lay the installation tunnel onto the mounting strips.
Caution:
The ends of the installation tunnel must be fitted with
edge protection!
Caution:
Do not route cables in the connection tunnel of in-line
installations!
Fix 2 self-adhesive cable clips (6) to the inner side of
the installation tunnel fig. 2
Fix cable in cable clips.
Servicing
The Backrest can be removed for massage unit servicing:
- Pull backrest (4) forward at the upper edge and
take away upwards.