Mitsubishi Electric City Multi PKFY-P NAMU-E Serie Manual De Instalación E Usuario página 12

5. Drainage piping work
I PKFY-P12/P15NGMU-E
1
A
3
A
Fig. 5-2
I PKFY-P18/P24/P30NFMU-E
H
A
Fig. 5-3
I PKFY-P06/P08NAMU-E
E
F
H
I
Fig. 5-4
I PKFY-P12/P15NGMU-E
A
C
B
D C
Fig. 5-5
I PKFY-P18/P24/P30NFMU-E
E
F
H
I
Fig. 5-6
12
2
a
b
4
B
A
C
B
D
G
E
F
I
EF
B
4 ( 100 )
D
A
G
A Gas pipe
B Liquid pipe
C Felt tape ∞
D Drain pipe
A
G
J
D
I PKFY-P12/P15NGMU-E (Fig. 5-2)
Preparing left and left rear piping
The drain hose can be connected at two different positions. Use the most convenient
position and, if necessary, exchange the position of the drain pan, rubber plug and
the drain hose.
1 Remove the drain cap.
• Remove the drain cap by holding the bit that sticks out at the end of the pipe and
pulling.
A Drain cap
2 Remove the drain hose.
• Remove the drain hose by holding on to the base of the hose a (shown by arrow)
and pulling towards yourself b.
3 Insert the drain cap.
• Insert a screwdriver etc into the hole at the end of the pipe and be sure to push to
the base of the drain cap.
4 Insert the drain hose.
• Push the drain hose until it is at the base of the drain box connection outlet.
• Please make sure the drain hose hook is fastened properly over the extruding drain
box connection outlet.
B Hooks
I PKFY-P18/P24/P30NFMU-E (Fig. 5-3)
The drain hose can be connected at two different positions. Use the most con-
venient position and, if necessary, exchange the position of the drain pan, rub-
ber plug and the drain hose.
A Drain pan F Insert the screwdriver into the hole of the rubber plug and push.
B Rubber plug G Exchange if necessary.
C Metal band H The screw of the metal clamp should be positioned facing the wall.
D Drain hose I Band (small) ¢
E Screwdriver
• Remove the drain hose after loosening the screw on the metal band used to mount
it.
• Securely insert both the rubber plug and drain hose into the drain outlets.
• Install the metal band around the drain hose and the small enclosed band around
the rubber plug. Be sure the bands are securely fastened so that there is no leak-
age.
5.2. Completing the piping
in.(mm)
I PKFY-P06/P08NAMU-E (Fig. 5-4)
Using the unit's pipe storage space (for left and left rear piping)
B
• To prevent condensation from dripping, put felt tape over the insulation materials
on the refrigerant and drain pipes within the unit as shown in the diagram.
C
• Arrange the drain hose so that it goes to the bottom of the unit.
• The overlapping width of felt tape is one half of the tape width.
A Felt tape £
B Liquid pipe
C Gas pipe
D Drain pipe
E Viewed from the back
F Take care that the middle of the drain hose is not raised.
G In the case of left piping, the refrigerant pipes and the drain pipe should be taped separately.
H Wrap together the refrigerant pipes and the drain pipe with felt tape so that white felt over-
laps by 25/32 in. (20 mm) or more.
* The pipes should be wrapped so that they are housed behind the unit.
I Fix the end of the felt tape with a bandage fixture.
I PKFY-P12/P15NGMU-E (Fig. 5-5)
Using the unit's pipe storage space (for left and left rear piping)
• To prevent cooling pipes from gathering moisture, wrap the pipes that are in the
unit's pipe storage space with the felt tape provided.
• When wrapping with the felt tape, be sure to double over by no more than half the
width of the tape.
• Use a bandage clip etc to fasten the end to the felt tape.
I PKFY-P18/P24/P30NFMU-E (Fig. 5-6)
Using the unit's pipe storage space (for left and left rear piping)
B
• To prevent dripping condensation, put felt tape over the insulation materials on the
refrigerant and drain pipes within the unit as shown in the diagram.
• Arrange the drain hose so that it goes to the bottom of the unit. Take care that the
middle of the drain hose is not raised.
A Felt tape ∞
B Liquid pipe
C Gas pipe
D Drain pipe
E Viewed from the back
F Two refrigerant pipes are wrapped together.
C
G A single drain hose is wrapped with felt tape.
H Two refrigerant pipes are wrapped with felt tape from the end of the bent section.
I Overlapping width of felt tape is one half of the tape width or less.
J Secure the end of the felt tape with a bandage fixture.