Overload Protection; Overheat Protection - Makita DUP361 Manual De Instrucciones

it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The tool does not work with only one battery
cartridge.
Tool / battery protection system
The tool is equipped with a tool/battery protection
system. This system automatically cuts off power to
the motor to extend tool and battery life. The tool will
automatically stop during operation if the tool or battery
is placed under one of the following conditions. In some
conditions, the lamps on the switch box lights up.

Overload protection

When the tool is operated in a manner that causes it to
draw an abnormally high current, the tool automatically
stops without any indication. In this situation, turn the
tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.

Overheat protection

When the tool is overheated, the tool stops automati-
cally, and the green lamp on the switch box blinks. In
this situation, let the tool cool down before turning the
tool on again.
Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically. And the red lamp on the switch box lights
up or blinks. If the product does not operate even when
the switches are operated, remove the batteries from
the battery holder and charge the batteries.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
►Fig.3: 1. Indicator lamps
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for few seconds.
Indicator lamps
Lighted Off
2. Check button
Remaining
capacity
Blinking
75% to 100%
50% to 75%
Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
CAUTION: Before connecting the battery to
the shears, always check to see that the switch
trigger actuates properly and returns to the "OFF"
position when released.
CAUTION: When not operating the tool, always
make sure that the I/O switch is on the "O" side.
CAUTION: Do not press the I/O switch to the "I"
(on) position while pulling the switch trigger. The
blade closes slightly and it may cause personal injury.
To turn on the tool, perform as follows:
1. Connect the switch box, connection cord, and
shears. (Refer to "Installing the connection cord".)
2. Hold the shears firmly, and press the I/O switch to
the "I" (on) position. The green pilot lamp lights up.
►Fig.4: 1. I/O switch
3. Pilot lamp (red)
3. The shear blades are locked-mode when the I/O
switch is on. To release the lock, pull the switch trigger
two times. The upper shear blade opens automatically.
4. To close the shear blade, pull the switch trigger.
►Fig.5: 1. Switch trigger
Auto locked-mode and shut-off
mode shift
For safety reasons, the tool shifts into locked-mode or
shut-off mode automatically if the tool is left untouched
for a certain period of time.
After 5 minutes: The tool shifts into locked-mode. Pull
the switch trigger two times to release the lock.
After 15 minutes: The tool is shift into shut-off mode,
and the green pilot lamp turns off. Press the I/O switch
to the "O" (off) position once, and press the I/O switch
to the "I" (on) position again, then pull the switch trigger
two times to release the lock.
Remaining
capacity
Blinking
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
2. Pilot lamp (green)
ENGLISH 11