Securyti Recommendation - Sima Elite 123 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ENG

7. SECURYTI RECOMMENDATION

VERY IMPORTANT: The earth connection must always be connected before start-up.
• Keep clear and clean the working area. A cluttered work area or workbench increases the risk of accidents.
• Do not expose the Power Tools to moisture. Make sure that the work area is well lit. Do not use Tools.
• Keep children away. Do not allow other people to touch the tool or the extension cord while operating the machine. In case of use
by children under 16, supervision is required.
• Respect the maximum level of acoustic pressure. Take adequate measures to protect the ears when the acoustic pressure ex-
ceeds the value of 85 dB (A).
• Hold the workpiece securely. Use clamps or a lathe to hold the work piece. It is safer than holding it with your hand and allows you
to use both hands to handle the tool.
• Be always alert and aware of what you are doing. Use common sense. Do not handle the tool when you are tired.
• Always use the right tool for every work. In this manual, it is indicated for what specific use this tool is intended. Do not use atta-
chable tools or devices weakly powered to perform heavy work. This tool will work better and provide greater security when used
according to its technical features.
• WARNING! The use of accessories, couplings or tools other than those recommended in this instruction manual may result in
injury to persons.
• Disconnect the machine from the mains before changing the cutting blade. The blade can heat up after intense work: wait for it to
cool before handling.
• Use standardized extension cables.
• Make sure that the voltage of the power supply network to which the machine is to be connected, matches the voltage indicated in
the adhesive label affixed to the machine.
• Make sure that the power extension cord of the machine does not meet high temperature points, oils, water, sharp edges, etc.
Make sure that it will not be stepped on or crushed by passing vehicles. Refrain from depositing objects on it
• Do not use pressurized water to clean the machine.
• Electrical cables shown cuts or peelings must be changed as soon as possible.
• Keep the safety elements and protections in place.
• Always use approved protection elements (gloves, safety helmet, glasses, boots...)
• Disconnect the machine from the mains after using it. Do not manipulate or operate the mechanical and electrical elements of the
machine while the engine is running.
• Cutting machines should be used only by people who are familiar with cutting operations.
• Be cautious and do not allow other people presence around the machine when it is working.
• Keep out people who are not familiar with the machine and do not let them access or handling it..
• Work clothes should not include loose fitting garments that could be trapped by moving parts of the machine.
• Before starting the machine, carefully read the instructions and observe compliance with safety regulations. Make sure you master
the way to stop the machine quickly and safely.
• Place the machine on a flat, well-lit surface. Do not connect it until its stability is perfect.
• Every time you need to move the machine, make sure to do it with the motor fully stopped and the moving parts blocked.
• Make sure to use best quality original cutting blades.
Additional safety rules for circular saws
• Always use sharpened blades of the appropriate type as designed for the workpiece. The recommended diameter of the blade is
indicated in the technical data shown on this manual.
• Do not force the blade forward to cut. If you push too hard the motor may stalk completely or partially potentially causing severe
damage. Let the motor reach full speed before starting the cut).
• Do not place your hands near the blade area when the saw is connected to the mains.
• Do not place your hands closer than 150 mm to the saw blade when cutting
• Do not use cutting discs that are damaged or cracked.
Residual risks
The use of masonry saws presents the following risks:
Despite compliance with the corresponding safety regulations and the use of safety devices, there are certain residual risks that
cannot be avoided, such as:
- Hearing problems.
- Accidents caused by the uncovered parts of the rotating saw disk.
- Injury when changing the saw blade.
- Health problems when breathing dust from not vacuumed cutting.
This machine must not be used in the rain. Cover it with waterproof materials. If the machine has been exposed to rainfall, check
before connecting that the electrical parts are not wet or damp. Always work in good lighting conditions.
Attention: All the safety recommendations indicated in this manual must be followed and the owner must comply with the occupatio-
nal risk prevention regulations of each place.
Manufacturer will not be held responsible for the consequences that may result from improper use of this masonry cutter.
7 7

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido