Timer Function - Taurus MIXING CHEF COMPACT Manual De Instrucciones

- Before using the product for the first time, clean
the parts that will come into contact with food in
the manner described in the cleaning section.
- Prepare the appliance according to the function
you wish to use.
USE:
- Take the length of cable required out of the
housing.
- Connect the appliance to the mains.
- -The LED display will light up, displaying 00:00
- Press gently with your hand on the upper part
while pressing the connect/disconnect button to
raise the upper part (Fig. 1)
- Place the bowl on base and position as shown
(Fig. 2)
- Place the accessory that will be used on the
mounting, ensuring that it fits over the hole
and turn in an anti-clockwise direction until it is
tightly fitted (Fig. 3)
- Press the connect/disconnect button and press
the upper part downwards until the button is
returned to its original position (Fig. 4)
- Put the lid on to prevent splashing.
- Start the appliance by turning on the speed
regulator.
- If no specific operating time has been program-
med, the LED display will show the time that
has elapsed since the operating speed was
selected.
- To avoid a fierce start up of the fan, it is advi-
sable to start off from the lowest speed position
and, once the fan has been switched on,
progressively increase the speed to the desired
position.
ELECTRONIC SPEED CONTROL:
- The speed of the appliance can be regulated
by using the speed regulator control (D). This
function is very useful, as it makes it possible to
adapt the power of the appliance to the type of
work that needs to be done.
- The speed control can be used for the desired
function as is described in the accessories
section.

TIMER FUNCTION:

- The appliance's operating time can be contro-
lled.
- To set an operating time simply select it by
using the time selection buttons (G) to a maxi-
mum of 10 minutes, with 10 second intervals.
By keeping "+" or "-" pressed, the selected time
will change more quickly.
- The programmed time or remaining time will be
shown on the LED display (F).
- By selecting the desired speed the LED display
will show the remaining time in 1 second inter-
vals.
- The time and operating of the appliance can be
paused by moving the selector knob to "0". Time
and operating will resume once the speed has
been selected again.
- Once the programmed time has elapsed, the
appliance will stop. Move the selector knob to
"0".
- To change the set time move the selector knob
to "0" and press "+" or "-" to reset the desired
time. Once selected, reset the desired operating
speed.
- To reset the timer, select "0" and then press
both select time buttons at the same time until
00:00 is shown on the LED display.
- If a specific operating time has not been set, the
LED display will show the time elapsed since
the operating speed was selected.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Turn off the appliance by selecting 0 on the
speed regulator.
- Unplug the appliance to the mains.
- Put the cable back in the cable housing.
- The cable housing enables the cable to be
stored and pulled out to the required length for
operating the appliance, preventing hazardous
situations.
- Take off the lid.
- Press the connect/disconnect button of the
upper part, while raising the upper part.
- Remove the bowl from the base by turning it in
an anti-clockwise direction.
- Clean the appliance
ACCESSORIES:
WHISK ACCESSORY (H):
- This accessory is used for whipping cream,
stiffening egg whites, making smoothies, light
cakes, meringues, mousses and soufflés.
- Do not use this accessory for mixing heavy
masses (e.g. fat and sugar) as it may damage
the appliance.
- Use the speed control to gradually increase until
reaching the maximum setting.
- Note: minimum quantity of 3 eggs, maximum
quantity of 12.