Peg-Perego ypsi Instrucciones De Uso página 22

attachment to be complete, press the two buttons
on the side of the handle bar (fig_b) and press the
handle bar until you hear it click (fig_c).
4 BASKET ASSEMBLY: Slip the basket flap into the slot
along the front bar of the chassis (Fig_a).
Fasten the basket eyelets to the buttons on each side
of the frame (fig_b).
5 To complete the basket attachment procedure for the
front part, you are required to insert the supplied tie
(fig_1) as follows:
position it between the basket and buttons, as shown
(fig_2) and use your finger to push downwards, so as
to complete the attachment procedure (fig_3).
Repeat the same procedure for the other side of the
basket.
6 Slip the back section of the pouch under the bar (fig.d).
Fasten the three buttons at the base of the chassis
(Fig.e).
Fasten the Velcro strap in the inside of the basket,
positioning the fabric as shown in the picture (Fig.f).
7 Close the pouch zip (fig.g).
Finally, to complete basket attachment, fasten the
basket buttons on both sides onto the chassis (fig.h).
WARNING! If you do not hook the basket on correctly,
as shown, the basket will be unable to support the
weight of loads placed in it.
8 The section of the front basket can be lowered (fig.a)
or raised (fig.b).
9 FIXED OR SWIVELLING FRONT WHEELS: to lock the
front wheels, rotate the lever anticlockwise onto the
locked padlock (fig_a), to release the wheels - turn
the lever clockwise to the unlocked padlock (fig_b).
On difficult terrain, we recommend using fixed
wheels.
10 BRAKE: press the lever down to apply the brake and
lock the frame. Do the opposite to release the brake.
11 ADJUSTABLE HANDLE BAR: to adjust the height of
the handlebar, pull the levers towards you (fig_a) and
move the handle bar until it clicks (fig_b). The handle
bar can be adjusted in several positions.
12 FOLDING: lock the front wheels into fixed position
(fig_a), put the handle bar to its lowest position
(fig b). Rotate the safety lever to the left (fig_c) and
pull the frame's internal handle towards you (fig_d).
Lift the handle until the frame is completely folded
(fig_e).
13 To fold correctly, make sure the side hook is engaged
(fig_a). When folded, the chassis will stand upright
(fig_b).
14 TRANSPORT: the stroller can be conveniently carried
(with the front wheels in fixed position) using the
central handle bar.
15 All the wheels can be removed to reduce dimensions
further. To remove the back wheels: pull the lever
downwards and remove the wheel as illustrated
(fig_a). To remove the front wheels: press the tab as
shown and remove the wheels (fig_b).
POSSIBLE USES
16
SERIAL NUMBERS
17 Ypsi Chassis, has the information on the product's
production date on the lower part of the frame.
_ Product name, production date and serial number of
the chassis. This information is essential in the event
of a claim.
INSTRUCTIONS
YPSI SEAT
1 OPENING: Before opening the Ypsi Seat, remove
(without using blades) any die-cut cardboard.
Open the seat from the ends, pulling until it clicks.
2 ATTACHING THE SEAT ONTO THE CHASSIS: To fasten
the Ypsi Seat, position it on the chassis (fig_a) and
press down with both hands until it clicks (fig_b).
Ensure the Ypsi Seat is properly attached.
3 The Ypsi Seat can be attached onto the chassis in
"world-facing" (fig_a) or "mum-facing" position
(fig_b).
Always engage the brake on the chassis before
fastening and unfastening the seat.
4 REMOVING THE YPSI SEAT FROM THE CHASSIS: To
unfasten the Ypsi Seat, press the levers near the
chassis attachments (fig_a) and lift the seat at the
same time (fig_b).
5 HOOD: to use the hood, stretch it until it clicks (so it is
completely open).
6 The hood comes with a mesh insert so that the baby
can be seen from any position. To use it, open the zips
(fig_a) and slide the hood's insert backwards (fig_b).
Alternatively, the hood can be stretched further
forwards (fig_c).
7 Sliding the hood's attachments on the uprights
(fig_a), you can vary its distance from the seat (fig_b).
8 ADJUSTING THE LEG REST: To switch from "sitting" to
"lying" or vice versa, simply press on the leg rest to
obtain the configuration you wish.
9 FRONT BAR: The front bar can be removed by pushing
the buttons on the sides (fig_a), or it can be opened
on one side pressing one button only (fig_b).
10 BED POSITION: the seat can be adjusted in
three positions, from "sitting" to "lying", with an
intermediate position (fig_a). To switch from one
position to another, pull the lever shown in the
picture (fig_b).
11 FOOT MUFF: to fasten the foot muff onto the Ypsi
Seat, close the zip on the side (fig_a) and do up the
buttons on the side of the corresponding uprights
(fig_b).
12 The foot muff can be opened at the front using the
zip for that purpose, as shown in the picture.
13 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles into the waist strap (with the straps attached
in the crotch strap) until you hear a click (fig_a). To
unfasten them, press the button which is situated at
the centre of the seatbelt buckle and pull the waist
strap outwards (fig_b).
14 To tighten the waist strap, pull on both sides in the
direction of the arrow; to loosen it, do the opposite.
15 The safety harness can be adjusted in 3 positions
according to the child's height. You must use the
higher positions as the child grows bigger.
16 Adjust the height, inserting the straps with shoulder
pads through the eyelet in the backrest (fig_a) and
pull them through the desired eyelets (fig_b).
17 FOLDING THE YPSI SEAT ATTACHED ONTO THE
CHASSIS: the Ypsi Seat can be folded attached on the
chassis only in world-facing position (fig_a).
To do this:
- the leg rest must be in "sitting" position,
- fold down the hood,
- pull the levers on the up-right (fig_b)
- fold Ypsi Seat onto itself (fig_c).
18 WARNING: If the seat is mum-facing it cannot
be folded attached onto the chassis. It must be
unfastened (fig_a).
It can take up less room when folded (fig_b) and can
be conveniently carried using the supplied handle
(fig_c).
19 OPENING THE CHASSIS WITH YPSI SEAT ATTACHED:
Press the side attachment fastener downwards, grip
the upper ends of the handle bar and rotate them
towards you until the chassis opens completely
(fig_a). Ypsi chassis open (fig_b). A "click" sound
means it has opened correctly and corresponds to the
attachment onto the base. Next, open the Ypsi Seat
from the ends, pulling it until it clicks (fig_c).
- 22 -